Hello

Chapter 14 – Semiconductor Electronics: Materials, Devices and Simple Circuits – 12th Physics

45โ€“68 minutes

14.0 Preview:

On the basis of conductivity, solids are classified as: Metals, Semi-Conductors and Insulators. The electrons reside in various orbits or energy bands around the nucleus, based on the energy they possess, like: Valence band and Conduction band. We shall extend this knowledge to study the energy levels that exist in metals, semi-conductors and insulators.

We shall then study about Intrinsic Semiconductors in some detail. An intrinsic semiconductor is a semiconductor in its purest form. We shall define Doping as the process of adding traces of impurities to an intrinsic semiconductor to increase its conductivity and the impurities added are called dopants. We will also look at extrinsic semiconductors. An Extrinsic semiconductor is an intrinsic semiconductor with small amount of added impurity. We shall study in some detail, the two types of extrinsic semiconductors: n-type and p type. We will see what happens at the p-n junction.

Further, we shall study the working of a semiconductor diode. A semiconductor diode is basically a p-n junction with metallic contacts provided at the ends for the application of an external voltage. Then, p-n junction diode under forward bias and under reverse bias shall be dealt with, in detail; when an external voltage, V is applied across p-n junction semiconductor diode in such a way that its p-region is connected to the positive terminal of the battery and n-region to the negative terminal, then it is said to be forward biased and when the external voltage, V is applied across the diode such that n-side is positive and p-side is negative, it is said to be reverse bias. Along these lines, we will study the application of junction-diode as a rectifier and its two types: Half wave and Full wave rectifier; Rectification is a process of converting AC to DC.

Then, we will take up the study of some special types of p-n junction diodes, like: Zener diode, Optoelectronic devices like photodiodes and Light emitting diode, Solar cells and junction transistor. We will look at the two types of transistors: p-n-p and n-p-n. We shall then look at the applications of a transistor as an amplifier. Finally, we will study a very interesting topic called, Digital electronics and logic gates under which we will study Boolean algebra which is the algebra followed by all electronic devices! Likewise, logic gates are electronic circuits which make logical decisions. Some of these logic gates are: OR, AND, NOT, NOR, NAND, X-OR, X-NOR gates. Each of these shall be dealt with in detail. We will end this chapter with the study of Integrated Circuits. The concept of fabricating an entire circuit on a small single block (or chip) of a semiconductor is known as Integrated Circuit (IC).

14.1 Introduction

Devices in which a controlled flow of electrons can be obtained are the basic building blocks of all the electronic circuits. In all the electronic devices, the flow of electrons takes place in a controlled manner may it be through vacuum, gasses or solids.

The triode has three electrodes that is, the cathode plate and grid, tetrode and pentrode each having 4-5 electrodes respectively. In a vacuum tube, the electrons are supplied by heated cathode and the controlled flow of these electrons in vacuum is obtained by varying the voltage between its different electrodes.

The vacuum devices in which electrons can flow only in one direction are called valves.

The disadvantage is that in bulk, they consume high power and work under high voltages.

The actual development of modern semiconductor electronics started taking place from 1930โ€™s. Some of the solid state semiconductors and their junctions offer the possibility of controlling the number and the direction of flow of charge carriers through them. Simple factors like light, heat, voltage can change can change the number of mobile charge carriers in a semiconductor.

In this chapter, we are going to study about the properties of semiconductors, junction diodes, bipolar junction transistors and the circuits illustrating their applications.

Questions for section 14.1

1. What are semiconductors?

2. Why the semiconductors are named so?

14.2 Classification of metals, conductors and semiconductors

On the basis of conductivity

On the basis of the relative values of electrical conductivity (s) or resistivity (r = 1/s ), the solids are broadly classified as:

  • Metals: They possess very low resistivity (or high conductivity).
    $$ ฯ \sim 10^{โ€“2} โ€“ 10^{โ€“8} \space \Omega \space m $$
    $$ ฯƒ \sim 10^2 โ€“ 10^8 \space Sm^{โ€“1} $$
  • Semiconductors: They have resistivity or conductivity intermediate to metals and insulators.
    $$ ฯ \sim 10^{โ€“5} โ€“ 10^6 \space \Omega \space m$$
    $$ฯƒ \sim 10^5 โ€“ 10^{โ€“6} \space Sm^{โ€“1} $$
  • Insulators: They have high resistivity (or low conductivity).
    $$ ฯ \sim 10^{11} โ€“ 10^{19} \space \Omega m$$
    $$ ฯƒ \sim 10^{โ€“11} โ€“ 10^{โ€“19} \space Sm^{โ€“1} $$

The values of r and s given above are indicative of magnitude and could well go outside the ranges as well. Relative values of the resistivity are not the only criteria for distinguishing metals, insulators and semiconductors from each other.

Some of the semiconductors are:

  • Elemental semiconductors
  • Compound semiconductor

On the basis of energy bands

  • Inside the crystal each electron has a unique position and no two electrons see exactly the same pattern of surrounding charges. Because of this, each electron will have a different energy level.
  • These different energy levels with continuous energy variation form what are called energy bands.
  • The energy band which includes the energy levels of the valence electrons is called the valence band.
  • The energy band above the valence band is called the conduction band.

With no external energy, all the valence electrons will reside in the valence band. If the lowest level in the conduction band happens to be lower than the highest level of the valence band, the electrons from the valence band can easily move into the conduction band.

Normally the conduction band is empty. But when it overlaps on the valence band electrons can move freely into it. This is the case with metallic conductors.

Some of the electrons from the valence band may gain external energy to cross the gap between the conduction band and the valence band. Then these electrons will move into the conduction band. At the same time they will create vacant energy levels in the valence band where other valence electrons can move. Thus the process creates the possibility of conduction due to electrons in conduction band as well as due to vacancies in the valence band.

Fig 14.1 The energy band positions in a semiconductor at 0 K. The upper band, called the conduction band, consists of infinitely large number of closely spaced energy states. The lower band, called the valence band, consists of closely spaced completely filled energy states.
The lowest energy level in the conduction band is shown as $E_C$ and highest energy level in the valence band is shown as $E_V$. Above $E_C$ and below $E_V$ there are a large number of closely spaced energy levels, as shown in figure. The gap between the top of the valence band and bottom of the conduction band is called the energy band gap.

Case 1

Fig 14.2 Difference between energy bands of metals
  • We can have a metal either when the conduction band is partially filled or the balanced band is partially empty or when the conduction and valance bands overlap.
  • When there is overlap electrons from valence band can easily move into the conduction band.
  • This situation makes a large number of electrons available for electrical conduction.
  • When the valence band is partially empty, electrons from its lower level can move to higher level making conduction possible. Therefore, the resistance of such materials is low or the conductivity is high.

Case 2

Fig 14.3 Difference between energy bands of insulators
  • There are no electrons in the conduction band, and therefore no electrical conduction is possible.
  • The energy gap is so large that electrons cannot be excited from the valence band to the conduction band by thermal excitation. This is the case of insulators.

Case 3

Fig 14.4
  • Because of the small band gap, at room temperature some electrons from valence band can acquire enough energy to cross the energy gap and enter the conduction band.
  • These electrons (though small in numbers) can move in the conduction band.
  • Hence, the resistance of semiconductors is not as high as that of the insulators.

Questions for section 14.2

1. Classify and explain in brief the classification of metals, insulators and semiconductors based on their conductivity.

2. Classify and explain in brief the classification of metals, insulators and semiconductors based on their energy bands.

3. With neat figures, explain the difference between energy bands of metals, insulators and semiconductors.

14.3 Intrinsic semiconductor

  • The semiconductors in their purest form are known as intrinsic semiconductors. Some of the examples are silicon and germanium.
  • In their crystal lattice, each atom has 4 valance electrons from 4 covalent bonds with the adjacent atoms.
  • At the temperature 0K, valance band of the intrinsic semiconductors is filled with electrons and the conductor is empty. Hence, the intrinsic semiconductor acts as insulator at 0K.
  • As the temperature increases, the covalent bond between the atoms starts breaking and electrons in the valance band gets energy and jumps into the conduction band due to thermal excitation called the hole.
  • It behaves as the positive charge in the valance band.
  • The holes in valance band cause hole current and exited electron in the conduction band causes electron current.
Fig 14.5

Fig 14.6 Schematic two-dimensional representation of Si or Ge structure showing covalent bonds at low temperature (all bonds intact). +4 symbol indicates inner cores of Si or Ge

  • Under the applied electric field, the hole drifts in the direction of electric field and electrons drift opposite to the direction of electric field.
  • Due to the thermal energies at T>0K, some valance electrons jump into the conduction band leaving equal number of holes in the valance band.

Fig 14.7 (a) An intrinsic semiconductor at T = 0 K behaves like insulator.
(b) At T > 0 K, four thermally generated electron-hole pairs.

Definition box
The process of adding traces of impurities to an intrinsic semiconductor to increase its conductivity is called doping and the impurities added are called dopants.

The dopant so added should be such that it doesnโ€™t distort the original pure semiconductor and occupies very few of the original semi-conductor atom sites in the crystal.

Example 14.1 C, Si and Ge have same lattice structure. Why is C insulator while Si and Ge intrinsic semiconductors?

Solution The 4 bonding electrons of C, Si or Ge lie, respectively, in the second, third and fourth orbit. Hence, energy required to take out an electron from these atoms (i.e., ionisation energy Eg ) will be least for Ge, followed by Si and highest for C. Hence, number of free electrons for conduction in Ge and Si are significant but negligibly small for C.

Questions for section 14.3

  1. Define intrinsic semiconductor.
  2. Give some of the examples of intrinsic semiconductor.
  3. How is hole current and electron current generated?
  4. Explain the energy band of a semiconductor with a neat diagram.
  5. What are dopants? Why are they added?
  6. Define doping.

14.4 Extrinsic semiconductor

When a small amount of impurity is added to the intrinsic semiconductor, that is, when it is doped, it is called extrinsic semiconductor. They are known as impure or doped semiconductors.

There are two types of dopants used in doping the tetravalent Si or Ge:

(i) Pentavalent: like Arsenic (As), Antimony (Sb), Phosphorous (P), etc. โ€“ has a valency of 5

(ii) Trivalent: like Indium (In), Boron (B), Aluminium (Al), etc. โ€“ has a valency of 3

The extrinsic semiconductors are of two types:

  1. n-type semiconductor
  2. p-type semiconductor

(i) n-type semiconductor

Fig 14.8 Commonly used schematic representation of n-type material which shows only the fixed cores of the substituent donors with one additional effective positive charge and its associated extra electron.

Fig 14.9 Pentavalent donor atom (As, Sb, P, etc.) doped for tetravalent Si or Ge giving n-type semiconductor

When a pentavalent impurity is added to a pure tetravalent semiconductor, it is called n-type semiconductor.

  • When an atom of +5 valency element occupies the position of an atom in the crystal lattice of Si, four of its electrons bond with the four silicon neighbours while the fifth remains very weakly bound to its parent atom.
  • This is because the four electrons participating in bonding are seen as part of the effective core of the atom by the fifth electron.
  • As a result the ionisation energy required to set this electron free is very small and even at room temperature it will be free to move in the lattice of the semiconductor.
  • For example, the energy required is ~ 0.01 eV for germanium, and 0.05 eV for silicon, to separate this electron from its atom.
  • Thus, the pentavalent dopant is donating one extra electron for conduction and hence is known as donor impurity.
  • The number of electrons made available for conduction by dopant atoms depends strongly upon the doping level and is independent of any increase in ambient temperature.
  • The number of free electrons generated by Si atoms, increases weakly with temperature.
  • With proper level of doping the number of conduction electrons can be made much larger than the number of holes.
  • Thus in an extrinsic semiconductor doped with pentavalent impurity, electrons become the majority carriers and holes the minority carriers.
Fig 14.10 Energy bands of n-type semiconductor at T > 0K

In the energy band diagram of n-type Si semiconductor, the donor energy level $E_D$ is slightly below the bottom $E_C$ of the conduction band and electrons from this level move into the conduction band with very small supply of energy. At room temperature, most of the donor atoms get ionised but very few $(\sim 10^{โ€“12})$ atoms of Si get ionised. So the conduction band will have most electrons coming from the donor impurities, as shown in figure above.

(ii) p-type semiconductor

Fig 14.11 Commonly used schematic representation of p-type material which shows only the fixed core of the substituent acceptor with one effective additional negative charge and its associated hole.

Fig 14.12 Trivalent acceptor atom (In, Al, B etc.) doped in tetravalent Si or Ge lattice giving p-type semiconductor

  • This is obtained when Si or Ge is doped with a trivalent impurity like Al, B, In, etc.
  • The dopant has one valence elec tron less than Si or Ge and, therefore, this atom can form covalent bonds with neighbouring three Si atoms but does not have any electron to offer to the fourth Si atom.
  • So the bond between the fourth neighbour and the trivalent atom has a vacancy or hole as shown in figure.
  • Since the neighbouring Si atom in the lattice wants an electron in place of a hole, an electron in the outer orbit of an atom in the neighbourhood may jump to fill this vacancy, leaving a vacancy or hole at its own site. Thus the hole is available for conduction.
  • Therefore, the dopant atom of p-type material can be treated as core of one negative charge along with its associated hole as shown in second figure.
  • These holes are in addition to the intrinsically generated holes while the source of conduction electrons is only intrinsic generation.
  • Thus, for such a material, the holes are the majority carriers and electrons are minority carriers.
Fig 14.13 Energy bands of p-type semiconductor at T > 0K.

For p-type semiconductor, the acceptor energy level $E_A$ is slightly above the top $E_V$ of the valence band as shown in figure above. With very small supply of energy an electron from the valence band can jump to the level $E_A$ and ionise the acceptor negatively. At room temperature, most of the acceptor atoms get ionised leaving holes in the valence band. Thus at room temperature the density of holes in the valence band is predominantly due to impurity in the extrinsic semiconductor. The electron and hole concentration in a semiconductor in thermal equilibrium is given by $ n_en_h = n_i^2 โ€ฆ..(14.5)$

The difference in the resistivity of C, Si and Ge depends upon the energy gap between their conduction and valence bands.

Example 14.2 Suppose a pure Si crystal has 5 ร— $10^{28}$ atoms $m^{โ€“3}$. It is doped by 1 ppm concentration of pentavalent As. Calculate the number of electrons and holes. Given that $n_i=1.5 ร— 10^{16} m^{โ€“3}$.

Solution: Note that thermally generated electrons ($ n_i \sim 10^{16} m^{โ€“3} $) are negligibly small as compared to those produced by doping.
Therefore, $ n_e \approx N_D$.
Since$ n_en_h = n^2_i$, The number of holes
$$ n_h= (2.25 ร— 10^{32})/(5 ร—10^{22}) $$
$$ \sim 4.5 ร— 10^9 m^{โ€“3} $$

Questions for section 14.4

  1. Explain in brief the n-type semiconductors.
  2. Explain in brief the p-type semiconductors.
  3. With diagrams, explain the energy bands for n and p type semiconductors.

14.5 p-n junctions

Fig 14.14 The p-n junction

A p-n junction is the basic building block of many semiconductor devices like diodes, transistor, etc. the representation of p-n junction is as shown in the figure above. We shall now discuss about how the junction is formed and how it behaves under the influence of external applied voltage.

14.5.1 p-n junction formation

  • As we know, by adding a small quantity of pentavalent impurity to a thin wafer of p-type silicon, a part of p-Si can be converted into n-Si. Now the wafer contains p-region and n-region and metallurgical junction between p and n junctions.
  • The two major processes that occur during the formation of p-n junction are diffusion and drift.
  • When a p-n junction is formed, the free electrons which are in higher concentration on n-side, diffuse over p-side diffuse over to n-side and combine with electrons and becomes neutral. These two motions of majority carriers give diffusion current across the junction.
  • When an electron diffuses from n to p, it leaves positively ionized immobile donor. Similarly when a hole diffuses from p to n, it leaves a negatively ionised immobile acceptor. As the diffusion charge carriers increases from either side, the opposite immobile charge concentration on either side of the junction increases.
Fig 14.15 p-n junction formation process

The space-charge region on either side of the junction which becomes free from mobile charge carriers is called as depletion region. The width of this region is 1/10th of a micrometer.

Fig 14.16

(a) Diode under equilibrium (V = 0)

(b) Barrier potential under no bias

Due to the positive space region on n-side of the junction and negative space charge region on p-side of the junction, an electric field is directed from positive charge towards negative charge which develops and causes a potential barrier. This barrier stops further diffusion of holes and electrons across the junction.

Due to the electric field near the junction, an electron on p-side of the junction moves to n-side and a hole on n-side of the junction moves to p-side. This causes the drift current to flow in the opposite direction to the diffusion current.

Initially, diffusion current is large and drift current is small. As the diffusion process continues, the space-charge regions on either side of the junction extend, thus increasing the electric field strength and hence drift current. This process continues until the diffusion current equals the drift current. Thus a p-n junction is formed. In a p-n junction under equilibrium there is no net current.

The loss of electrons from the n-region and the gain of electron by the p-region causes a difference of potential across the junction of the two regions. The polarity of this potential is such as to oppose further flow of carriers so that a condition of equilibrium exists. Figure shows the p-n junction at equilibrium and the potential across the junction.
The n-material has lost electrons, and p material has acquired electrons. The n material is thus positive relative to the p material. Since this potential tends to prevent the movement of electron from the n region into the p region, it is often called a barrier potential.

Example 14.3 Can we take one slab of p-type semiconductor and physically join it to another n-type semiconductor to get p-n junction?

Solution No! Any slab, howsoever flat, will have roughness much larger than the inter-atomic crystal spacing ($ \sim $ 2 to 3 ร…) and hence continuous contact at the atomic level will not be possible. The junction will behave as a discontinuity for the flowing charge carriers.

Questions for section 14.5

  1. Explain the formation of p-n junction with neat figures.

14.6 Semiconductor diode

Fig 14.17 (a) Semiconductor diode (b) Symbol for p-n junction diode

A semiconductor diode is basically a p-n junction with metallic contacts provided at the ends for the application of an external voltage. It is a two terminal device. A p-n junction diode is symbolically represented as shown in second figure.

The direction of arrow indicates the conventional direction of current. The equilibrium barrier potential can be altered by applying an external voltage V across the diode.

14.6.1 p-n junction diode under forward bias

Fig 14.18 (a) p-n junction diode under forward bias (b) Barrier potential (1) without battery, (2) Low battery voltage, and (3) High voltage battery.

When an external voltage V is applied across p-n junction semiconductor diode in such a way that its p-region is connected to the positive terminal of the battery and n-region to the negative terminal, then it is said to be forward biased.

Most of the applied voltage drops across the depletion region. As the applied voltage is opposite to the built in barrier potential $V_o$, width of the depletion layer decreases and barrier height is reduced. The effective barrier height under forward bias is given by ($V_o \sim V $)

If the applied voltage is small, the barrier potential will be reduced only slightly below the equilibrium value, and only a small number of carriers in the materialโ€”those that happen to be in the uppermost energy levelsโ€”will possess enough energy to cross the junction. So the current will be small.

If we increase the applied voltage significantly, the barrier height will be reduced and more number of carriers will have the required energy. Thus the current increases.

Due to the applied voltage, electrons from n-side cross the depletion region and reach p-side. Similarly, holes from p-side cross the junction and reach the n-side. This process under forward bias is known as minority carrier injection

Due to this concentration gradient, the injected electrons on p-side diffuse from the junction edge of p-side to the other end of p-side. Likewise, the injected holes on n-side diffuse from the junction edge of n-side to the other end of n-side as shown in following figure.

Fig 14.19 Forward bias minority carrier injection

This motion of charged carriers on either side gives rise to current. The total diode forward current is sum of hole diffusion current and conventional current due to electron diffusion. The magnitude of this current is usually in mA.

14.6.2 p-n junction diode under reverse bias

Fig 14.20 (a) Diode under reverse bias (b) Barrier potential under reverse bias
  • When an external voltage (V) is applied across the diode such that n-side is positive and p-side is negative, it is said to be reverse biased as shown in first figure.
  • The applied voltage mostly drops across the depletion region. The barrier height increases and the depletion region widens due to the change in the electric field.
  • The electron flow is supressed from n to p and from p to n. Thus, diffusion current, decreases enormously compared to the diode under forward bias.
  • The electric field direction of the junction is such that if electrons on p-side or holes on n-side in their random motion come close to the junction, they will be swept to its majority zone. This drift of carriers gives rise to current.
  • Even a small voltage is sufficient to sweep the minority carriers from one side of the junction to the other side of the junction.
  • The current under reverse bias is essentially voltage independent up to a critical reverse bias voltage, known as breakdown voltage ($V_{br}$ ).
  • Even a slight increase in the bias voltage causes large change in the current. If the reverse current is not limited by an external circuit below the rated value the p-n junction will get destroyed. Once it exceeds the rated value, the diode gets destroyed due to overheating.
  • The circuit arrangement for studying the V-I characteristics of a diode are shown in figures below.
Fig 14.21
  • The battery is connected to the diode through a potentiometer (or reheostat) so that the applied voltage to the diode can be changed.
  • For different values of voltages, the value of the current is noted. A graph between V and I is obtained as shown in the graph above.
  • Forward bias, the current first increases very slowly, almost negligibly, till the voltage across the diode crosses a certain value.
  • After the characteristic voltage, the diode current increases significantly (exponentially), even for a very small increase in the diode bias voltage. This voltage is called the threshold voltage or cut-in voltage.
  • For the diode in reverse bias, the current is very small (~ฮผA) and almost remains constant with change in bias. It is called reverse saturation current.

Example 14.4 The V-I characteristic of a silicon diode is shown in the Fig. 14.22. Calculate the resistance of the diode at (a)$ I_D$= 15 mA and (b) $V_D$ = โ€“10 V.

Fig 14.22

Solution

Considering the diode characteristics as a straight line between I = 10 mA to I = 20 mA passing through the origin, we can calculate the resistance using Ohmโ€™s law.

(a) From the curve, at I = 20 mA, V = 0.8 V, I = 10 mA, V = 0.7 V
$$ r_{fb}= \Delta V/ \Delta I = 0.1V/10 mA = 10 \Omega $$

(b) From the curve at V = โ€“10 V, I = โ€“1 ฮผA,
Therefore, $ r_{rb} = 10 V/1ฮผA= 1.0 ร— 10^7 \Omega $

Questions for section 14.6

  1. What happens to p-n junction under forward bias?
  2. What is minority carrier injection?
  3. What happens to p-n junction under reverse bias?

14.7 Application of junction diode as a rectifier

  • Rectifier converts AC to DC.
  • Rectification is a process of converting AC to DC.
  • There are 2 types of rectification. They are:

1. Half wave rectification

2. Full wave rectification

Half-wave rectifier

  • A p-n junction can also be used as half-wave rectifier.
  • The circuit part of a half-wave rectifier includes the input AC voltage applied across the ends of the primary transformer. The load resistance RL is connected between the ends of secondary diode D.
Fig 14.23 (a) Half-wave rectifier circuit
(b) Input ac voltage and output voltage waveforms from the rectifier circuit

Working

  • When the positive half cycle of the input AC appears across the secondary, A is positive with respect to B.
  • Hence the diode is forward biased and the current flows across the junction through a load resistance.
  • A pulsating DC appears across the secondary when A will be negative with respect to B, so the diode is reverse biased. No current flows through the circuit.
  • The same process continues and negative half cycles are supressed and positive half cycles are rectified.
  • The output DC is pulsating and unidirectional.
  • This is smothered using a filter circuit. Thus the p-n junction behaves as half-wave rectifier.

Efficiency

  • The ratio of D.C power output to the applied input A.C power is known as rectifier efficiency.
    $$ n = \frac { Output \space D.C \space power }{ Input \space A.C Power} = \frac { P_{DC}}{P_{AC}} $$
  • In Half โ€“ wave rectification a maximum of 40.6 % of A.C power is converted into D.C power.
  • In Half โ€“ wave rectification $ n = \frac { 0.406(R_L)}{r_f + R_L} $
    Where $R_L $ = load resistor , $r_f$ = diode forward resistance.

Full-wave rectifier

Circuit

  • The setup includes an input AC voltage is applied across terminals of the primary transformer.
  • Between the terminals of secondary, two junction diodes $D_1$ and $D_2$ and the load resistance $R_L$ are connected as shown in the figure below.
Fig 14.24 (a) A Full-wave rectifier circuit
(b) Input wave forms given to the diode $D_1$ at A and to the diode $D_2$ at B;
(c) Output waveform across the load $R_L$ connected in the full-wave rectifier circuit

Working

  • When the positive half cycle of input AC appears across the secondary, A is positive with respect to B. So, $D_1$ is forward biased and $D_2$ is reverse biased.
  • Current flows in the load from X to Y due to $D_1$ when negative half cycles appear across secondary, A is negative with respect to B.
  • $S_oD_1$ is reverse biased and $D_2$ is forward biased. So, the current flows in the load in the same direction from X to Y.
  • The output voltage is pulsating, but, unidirectional.
  • The process repeats and both positive and negative half cycles are rectified.
  • The output DC is pulsating.
  • This is smothered using filter.
  • Thus, full-wave rectifier using p-n junction diode.

Efficiency

$$ n = \frac { Output \space D.C \space power }{ Input \space A.C Power} = \frac { P_{DC}}{P_{AC}} $$

In full wave rectifications , a maximum of 81.2 % of A.C power is converted into D.C power.

In full waves rectifications, $ n = \frac { 0.812(R_L)}{r_f+R_L} $

Filter circuit

Fig 14.25

Fig 14.25
(a) A full-wave rectifier with capacitor filter
(b) Input and output voltage of rectifier in (a)

The rectified voltage is in the form of pulses of the shape of half sinusoids. Though it is unidirectional it does not have a steady value. To get steady dc output from the pulsating voltage normally a capacitor is connected across the output terminals. One can also use an inductor in series with RL for the same purpose. Since these additional circuits appear to filter out the ac ripple and give a pure dc voltage, so they are called filters.

When the voltage across the capacitor is rising, it gets charged. If there is no external load, it remains charged to the peak voltage of the rectified output. When there is a load, it gets discharged through the load and the voltage across it begins to fall. In the next half-cycle of rectified output it again gets charged to the peak value.

The rate of fall of the voltage across the capacitor depends upon the inverse product of capacitor C and the effective resistance RL used in the circuit and is called the time constant. To make the time constant large value of C should be large. So capacitor input filters use large capacitors. The output voltage obtained by using capacitor input filter is nearer to the peak voltage of the rectified voltage. This type of filter is most widely used in power supplies.

Questions for section 14.7

  1. What is a rectifier?
  2. What is rectification?
  3. What are the types of rectification?
  4. With a neat diagram and graph, explain half-wave rectifier.
  5. With a neat diagram and graph, explain full-wave rectifier.
  6. Give equations for efficiency of half and full wave rectifier.
  7. What is filter circuit? Explain using figure and graph.

14.8 Special purpose p-n junction diodes

14.8.1 Zener diode

Fig 14.26 Zener diode, (a) symbol, (b) I-V characteristics
Definition box
A properly doped diode with a sharp breakdown voltage in reverse bias is called Zener diode.

Zener effect

When the reverse bias voltage is increased, reverse bias current also slightly increases. At a particular reverse bias voltage, reverse bias current suddenly increases to enormous value due to breakdown of the junction. The voltage is called zener voltage and the effect is called zener effect.

Characteristics of Zener diode

  1. A properly doped diode with sharp breakdown voltage.
  2. It is always to be connected in reverse bias.
  3. A zener diode has sharp breakdown voltage called zener breakdown voltage.
  4. When it is forward biased, its characteristics are like that of an ordinary diode.
  5. By changing the doping concentrations, Zener diodes with widely different zener voltage can be designed.
  6. They have high thermal stability and can accommodate large current without getting burnt out.
  7. At zener voltage, the diode voltage remains constant over a wide range of work.

Uses

  1. It is used as a voltage regulator to provide constant PD in a source where fluctuation of current exists.
  2. Even during the fluctuations, the PD across the diode remains constant as it is working at zener voltage.

Zener diode as a voltage regulator

Fig 14.27 Zener diode as DC voltage regulator
  • When the ac input voltage of a rectifier fluctuates, its rectified output also fluctuates. To get a constant dc voltage from the dc unregulated output of a rectifier, we use a Zener diode.
  • The unregulated dc voltage is connected to the Zener diode through a series resistance $R_s$ such that the Zener diode is reverse biased.
  • If the input voltage increases, the current through $R_s$ and Zener diode also increases. This increases the voltage drop across $R_s$ without any change in the voltage across the Zener diode.
  • This is because in the breakdown region, Zener voltage remains constant even though the current through the Zener diode changes.
  • Similarly, if the input voltage decreases, the current through $R_s$ and Zener diode also decreases. The voltage drop across $R_s$ decreases without any change in the voltage across the Zener diode.
  • Thus any increase/decrease in the input voltage results in, increase/decrease of the voltage drop across $R_s$ without any change in voltage across the Zener diode.
  • Thus the Zener diode acts as a voltage regulator.

Example 14.5 In a Zener regulated power supply a Zener diode with $V_Z$ = 6.0 V is used for regulation. The load current is to be 4.0 mA and the unregulated input is 10.0 V. What should be the value of series resistor $R_S$?

Solution:

The value of$ R_S$ should be such that the current through the Zener diode is much larger than the load current. This is to have good load regulation. Choose Zener current as five times the load current, i.e.,$I_Z$= 20 mA. The total current through $R_S$ is, therefore, 24 mA. The voltage drop across $R_S$ is 10.0 โ€“ 6.0 = 4.0 V. This gives $R_S = 4.0V/(24 ร— 10^{โ€“3}) A = 167 \Omega $. The nearest value of carbon resistor is $ 150 \Omega $. So, a series resistor of $ 150 \Omega $ is appropriate. Note that slight variation in the value of the resistor does not matter, what is important is that the current $I_Z$ should be sufficiently larger than $I_L$.

14.8.2 Optoelectronic junction devices

Let us now study the functioning of the following optoelectronic devices:

  1. Photodiodes used for detecting optical signal (photo-detectors).
  2. Light emitting diodes (LED) which convert electrical energy into light.
  3. Photovoltaic devices which convert optical radiation into electricity (solar cells).

Photodiode

Fig 14.28 (a) An illuminated photodiode under reverse bias
(b) I-V characteristics of a photodiode for different illumination intensity $I_4 > I_3 > I_2 > I_1$
  • A Photodiode is again a special purpose p-n junction diode fabricated with a transparent window to allow light to fall on the diode.
  • It is operated under reverse bias.
  • When the photodiode is illuminated with light (photons) with energy (hv) greater than the energy gap (Eg) of the semiconductor, then electron-hole pairs are generated due to the absorption of photons.
  • The diode is fabricated such that the generation of e-h pairs takes place in or near the depletion region of the diode.
  • Due to electric field of the junction, electrons and holes are separated before they recombine.
  • The direction of the electric field is such that electrons reach n-side and holes reach p-side. Electrons are collected on n-side and holes are collected on p-side giving rise to an emf. When an external load is connected, current flows.
  • The magnitude of the photocurrent depends on the intensity of incident light.
  • Thus photodiode can be used as a photo-detector to detect optical signals.

Example 14.6 The current in the forward bias is known to be more($ \sim $mA) than the current in the reverse bias ($ \sim $ฮผA). What is the reason then to operate the photodiodes in reverse bias?

Solution Consider the case of an n-type semiconductor. Obviously, the majority carrier density (n) is considerably larger than the minority hole density p (i.e., n >> p). On illumination, let the excess
electrons and holes generated be $\Delta $n and $\Delta$ p, respectively:
$$ nโ€™ = n + \Delta n $$
$$ p`= p +\Delta p $$
Here nโ€™ and pโ€™ are the electron and hole concentrations* at any particular illumination and n and p are carriers concentration when there is no illumination. Remember $\Delta n $ =$\Delta p $and n >> p. Hence, the fractional change in the majority carriers (i.e., $ \Delta n$/n) would be much less than that in the minority carriers (i.e., $ \Delta p$/p). In general, we can state that the fractional change due to the photo-effects on the minority carrier dominated reverse bias current is more easily measurable than the fractional change in the forward bias current. Hence, photodiodes are preferably used in the reverse bias condition for measuring light intensity.

Light emitting diode

Fig 14.29 Light emitting diode
  • It is a heavily doped p-n junction which under forward bias emits spontaneous radiation. The diode is encapsulated with a transparent cover so that emitted light can come out.
  • When the diode is forward biased, electrons are sent from n to p and holes are sent from p to n.
  • At the junction boundary the concentration of minority carriers increases compared to the equilibrium concentration.
  • Thus at the junction boundary on either side of the junction, excess minority carriers are there which recombine with majority carriers near the junction.
  • On recombination, the energy is released in the form of photons. Photons with energy equal to or slightly less than the band gap are emitted.
  • When the forward current of the diode is small, the intensity of light emitted is small. As the forward current increases, intensity of light increases and reaches a maximum.
  • Further increase in the forward current results in decrease of light intensity. LEDs are biased such that the light emitting efficiency is maximum.
  • Care should be taken that high reverse voltages do not appear across them.
  • LEDs that can emit red, yellow, orange, green and blue light are commercially available.
  • LEDs have the following advantages over conventional incandescent low power lamps:
  1. Low operational voltage and less power.
  2. Fast action and no warm-up time required.
  3. The bandwidth of emitted light is 100 ร… to 500 ร… or in other words it is nearly monochromatic.
  4. Long life and ruggedness.
  5. Fast on-off switching capability.

Solar cell

Fig 14.30 (a) Typical p-n junction solar cell (b) Cross-sectional view
  • A solar cell is basically a p-n junction which generates emf when solar radiation falls on the p-n junction.
  • It works on the same principle as the photodiode, except that no external bias is applied and the junction area is kept much larger for solar radiation to be incident.
  • A p-Si wafer of about 300 ฮผm is taken over which a thin layer (~0.3 ฮผm) of n-Si is grown on one-side by diffusion process.
  • The other side of p-Si is coated with a metal.
  • On thetop of n-Si layer, metal finger electrode. This acts as a front contact.
  • The metallic grid occupies only a very small fraction of the cell area (<15%) so that light can be incident on the cell from the top.
  • The generation of emf by a solar cell, when light falls on, it is due to the following three basic processes: generation, separation and collection:
    • generation of e-h pairs due to light (with hn > Eg ) close to the junction;
    • Separation of electrons and holes due to electric field of the depletion region. Electrons are swept to n-side and holes to p-side;
    • The electrons reaching the n-side are collected by the front contact and holes reaching p-side are collected by the back contact. Thus p-side becomes positive and n-side becomes negative giving rise to photo voltage.
    • When an external load is connected as shown in the figure a photocurrent IL flows through the load. A typical I-V characteristic of a solar cell is shown in the figure.
  • Solar cells are used to power electronic devices in satellites and space vehicles and also as power supply to some calculators.
Fig 14.31 (a) A typical illuminated p-n junction solar cell (b) I-V characteristics of a solar cell

Example 14.7 Why are Si and GaAs are preferred materials for solar cells?

Solution The solar radiation spectrum received by us is shown in Fig. 14.32.

Fig 14.32

The maxima is near 1.5 eV. For photo-excitation,$ h ฮฝ > E_g$. Hence, semiconductor with band gap ~1.5 eV or lower is likely to give better solar conversion efficiency. Silicon has $E_g$ ~ 1.1 eV while for GaAs it is ~1.53 eV. In fact, GaAs is better (in spite of its higher band gap) than Si because of its relatively higher absorption coefficient. If we choose materials like CdS or CdSe ($E_g$ ~ 2.4 eV), we can use only the high energy component of the solar energy for photo-conversion and a significant part of energy will be of no use.The question arises: why we do not use material like PbS ($E_g$ ~ 0.4 eV)which satisfy the condition h ฮฝ > $E_g$ for n maxima corresponding to the solar radiation spectra? If we do so, most of the solar radiation will be absorbed on the top-layer of solar cell and will not reach in or near the depletion region. For effective electron-hole separation, due to the junction field, we want the photo-generation to occur in the junction region only.

Questions for section 14.8

  1. What is zener diode? What are the zener effects?
  2. State some of the properties of zener diode.
  3. How can zener diode be used as voltage regulator?
  4. State some of the optoelectronic devices.
  5. Explain in brief the photo-diode.
  6. Explain in brief the light emitting diode.
  7. Explain in brief the solar cell.
  8. State some of the advantages of photodiode, light emitting diode and solar cell.

14.9 Junction transistor

Transistor basically means trans-resistor. This was discovered by John Bardeen W H Brattain and William Shockley. This is a 3 terminal forming two junction device whose basic action is amplification.
There are two types of transistors.

1. n-p-n transistor

Fig 14.33

2. p-n-p transistor

Fig 14.34

14.9.1 Transistor: structure and action

  • An n-p-n transistor is made up of a p-type semiconductor. The semiconductor is sandwiched between two n-type.
  • A p-n-p transistor is made up of n-type sandwiched between two p-type semiconductors.
    In both the transistors, the central region is called base and the other two regions are called emitter and collector.
  • Emitter (E): it is the region of the transistor which emits charge like electrons or holes is called emitter. This is heavily doped compared to other regions.
  • Collector (C): this is the region of transistor which collects the charge carriers. This region is moderately doped.
  • Base (B): base is the middle region of transistor. It acts as a confront region which is very lightly doped.

Working of an n-p-n transistor

Fig 14.35 bBias Voltage applied on p-n-p transistor
  • In this type of transistor, the emitter being an n-type material, possess electrons as majority charge carriers.
  • Since the E-B junction is forward biased, the electrons from the emitter cross the junction and enter the base region. This constitutes to the emitter current.
  • As these electrons flow through the p-type base region, they tend to combine with majority charge carriers in that region.
  • The loss of charge in the base results in base current.
  • The combining electrons get lightly doped.
  • The remaining electrons cross the B-E junction and are collected by the collector. This results in collector current.
    $$ I_e = I_b + I_c $$
  • The base current is very small and is in microamperes by controlling the base current, the collector current can be controlled.

Working of p-n-p transistor

Fig 14.36 Bias Voltage applied on n-p-n transistor
  • In this type of transistor, the emitter being a p-type material it possesses of holes as majority charge carrier forward biased holes form the emitter cross the junction and enters the base region.
  • This constitutes to the base current as their holes flows through carriers that is electrons in that region.
  • The loss of charge in the base results in the base current.
  • The number of holes combining the base is very lightly doped.
  • The remaining holes cross the base collector junction and are collected by the collector.
  • This results in the collector current.
    $$ I_e = I_b + I_c $$

14.9.2 Basic transistor circuit configurations and transistor characteristics

The transistor can be connected in any of the following three configurations:

Common Emitter (CE)

Common Base (CB)

Common Collector (CC)

The transistor is most widely used in the CE configuration and we shall restrict our discussion to only this configuration. Since more commonly used transistors are n-p-n Si transistors, we shall confine our discussion to such transistors only. With p-n-p transistors the polarities of the external power supplies are to be inverted.

Common emitter transistor characteristics

Fig 13.37 Circuit arrangement for studying the input and output characteristics of n-p-n transistor in CE configuration
  • The variation of the base current $I_B$ with the base-emitter voltage $V_{BE}4 is called the input characteristic.
  • The variation of the collector current IC with the collector-emitter voltage VCE is called the output characteristic.
  • The output characteristics are controlled by the input characteristics. This implies that the collector current changes with the base current.
Fig 13.38 (a) Typical input characteristics (b) Typical output characteristics
  • The collector-emitter voltage $V_{CE}$ is kept fixed while studying the dependence of IB on VBE.
  • The collector -emitter voltage $V_{CE}$ is kept large enough to make the base collector junction reverse biased. Since
    $$ V_{CE} = V_{CB} + V_{BE} $$
    and for Si transistor $V_{BE}$ is 0.6 to 0.7 V, VCE must be sufficiently larger than 0.7 V.
  • Since the transistor is operated as an amplifier over large range of $V_{CE}$, the reverse bias across the base-collector junction is high most of the time.
  • Therefore, the input characteristics may be obtained for $V_{CE}$ somewhere in the range of 3 V to 20 V.
  • Since the increase in $V_{CE}$ appears as increase in $V_{CB}$, its effect on IB is negligible. As a consequence, input characteristics for various values of $V_{CE}$ will give almost identical curves.
  • Hence, it is enough to determine only one input characteristics.
  • The output characteristic is obtained by observing the variation of $I_C$ as $V_{CE}$ is varied keeping $I_B$ constant.
  • if $V_{BE}$ is increased by a small amount, both hole current from the emitter region and the electron curren from the base region will increase.
  • As a consequence both $I_B$ and $I_C$ will increase proportionately. This shows that when $I_B$ increases $I_C$ also increases.
  • The linear segments of both the input and output characteristics can be used to calculate some important ac parameters of transistors as shown below.
    • Input resistance ($r_i$ )
      This is defined as the ratio of change in base-emitter voltage to the resulting change in base current at constant collector-emitter voltage. This is dynamic and as can be seen from the input characteristic, its value varies with the operating current in the transistor:
      $$ r_i = \bigg( \frac { \Delta V_{BE}}{ \Delta I_B} \bigg){V{CE}} $$
    • Output resistance ($r_o$)
      This is defined as the ratio of change in collector-emitter voltage to the change in collector current at a constant base current IB. $$ r_o = \bigg( \frac { \Delta V_{CE}}{ \Delta I_C } \bigg)_ {I_B} $$ The output characteristics show that initially for very small values of $V_{CE}$, $I_C$ increases almost linearly. This happens because the base-collector junction is not reverse biased and the transistor is not in active state. The transistor is in the saturation state and the current is controlled by the supply voltage $V_{CC} (=V_{CE})$ in this part of the characteristic. When $V_{CE}$ is more than that required to reverse bias the base-collector junction, $I_C$ increases very little with $V_{CE}$. The reciprocal of the slope of the linear part of the output characteristic gives the values of ro.
      The output resistance of the transistor is mainly controlled by the bias of the base-collector junction.
    • Current amplification factor (b): This is defined as the ratio of the change in collector current to the change in base current at a constant collector-emitter voltage ($V_{CE}$) when the transistor is in active state.
      $$ ฮฒ{ac} = \bigg( \frac { \Delta I_C}{ \Delta I_B} \bigg){V_{CE}} $$
      This is also known as small signal current gain and its value is very large.

Example 14.8 From the output characteristics shown in Fig. 14.30(b),calculate the values of $ฮฒ{ac}$ and $ฮฒ{ dc}$ of the transistor when $V_ {CE}$ is 10 V and $I_C$ = 4.0 mA.

Solution: $ฮฒ{ac} = \frac { \Delta I_c}{ \Delta I b} $ , $ ฮฒ{ dc} = \frac { I_c}{ I b} $

For determining $ฮฒ{ac}$ and $ฮฒ{ dc}$ at the stated values of $V_{CE} $ and $I_C$ one can
proceed as follows. Consider any two characteristics for two values of $I_B$ which lie above and below the given value of $I_C$ . Here $I_C$ = 4.0 mA. (Choose characteristics for $I_B$= 30 and 20 ฮผA.) At $V_{CE} $ = 10 V we read the two values of $I_C$ from the graph. Then $ \Delta I_B =(30-20) ฮผA = 10 ฮœa $, $ \Delta I_c =(4.5-3.0) mA = 1.5 mA $

Therefore, $ฮฒ{ac} $ = 1.5 mA/ 10 ฮผA = 150 For determining $ฮฒ{dc} $ , either estimate the value of $I_B$ corresponding to $I_C$ = 4.0 mA at $V_{CE}$ = 10 V or calculate the two values of $ฮฒ{dc} $ for the two characteristics chosen and find their mean. Therefore, for $I_C$= 4.5 mA and $I_B$= 30 ฮผA, $ฮฒ{dc} $ = 4.5 mA/ 30 ฮผA = 150 and for$ I_C$ = 3.0 mA and $I_B$ = 20 ฮผA

$ฮฒ{dc} $ =3.0 mA / 20 ฮผA = 150 Hence, $ฮฒ{dc} $ =(150 + 150) /2 = 150

14.9.3 Transistor as a device

The transistor can act as a switch when it is used in cut off or saturation state. For using the transistor as an amplifier, it has to operate in the active region.

Fig 14.39 (a) Base-biased transistor in CE configuration (b) Transfer characteristic

We will now try to study the operation of transistor as a switch by analysing the behaviour of base-biased transistor in CE configuration as shown in the figure.

By applying Kirchoffโ€™s voltage rule to input and output sides of the circuit we get, $ V_{BB} = I_BR_B + V_{BE} \space and \space V_{CE} = V_{CC} โ€“ I_CR_C $

We shall treat $V_{BB}$ as the dc input voltage $V_i$ and $V_{CE}$ as the dc output voltage $V_o$. So we have, $ V_i = I_BR_B +V_{BE} \space and \space V_o = V_{CC} – I_CR_C $

Let us see how $V_o$ changes as $V_i$ increases from zero onwards . In the case of Si transistor , as long as input $V_i$ is less than 0.6 V , the transistor will be in cut off state and current $I_C$ will be zero.

Hence,
$$ V_o = V_{CC} $$

We will now try to understand how the transistor acts as a switch. As long as the $V_i$ is low and unable to forward bias the transistor, $V_0$ is high. If $V_i$ is high enough to drive the transistor into saturation, then $V_o$ is low and very near to zero.

When the transistor is not conducting it is said to be switched off and when it is driven into saturation it is said to be switched on. This shows that if we define low and high states as below and above certain voltage levels corresponding to cut-off and saturation of the transistor, then we can say that a low input switches the transistor off and a high input switches off when it is driven into saturation it is said to be switched on.

We can conclude that the low input to transistor gives high output and high input gives low output.

Transistor as an amplifier

Definition box
The process of raising the strength of weak input signal to strong output signal is called amplification.
The device which increases the weak input signal into strong output signal is called amplifier.

The amplifiers are of two types

  1. Power amplifier
    The amplifier which is used to raise the power level is called as the power amplifier.
  2. Voltage amplifier
    The amplifier which is used to raise the voltage level is known as voltage amplifier.

14.9.4 Transistor as an Amplifier (CE-Configuration)`

Fig 14.40 A simple circuit of a CE-transistor amplifier
  • The transistor can be used as an amplifier when we use the active region of the $V_0 v/s V_1$ curve.
  • The slope of the linear part of the curve represents the rate of change of output with the input. This result is negative.
  • The input voltage of CE amplifier increases as the output voltage decreases and the output voltage decreases and the output is said to be out of phase with the input.
  • If we consider $ฮ”V_o$ and $ฮ”V_1$ as small changes in the output and input voltages then, $ฮ”V_o / ฮ”V_1$ is called small signal voltage gain Av of the amplifier.

We have , $V_o = V_{CC} โ€“ I_CR_C $
Therefore , $ \Delta V_o = 0 โ€“ R_C \Delta I_C $
Similarly , from $V_i = I_BR_B +V_{BE} $
$$ \Delta V_i = R_B \Delta I_B + \Delta V_{BE} $$
But $ \Delta V_{BE}$ is negligibly small in comparison to $ \Delta I_BR_B $ in this circuit. So, the voltage gain of this CE amplifier is given by
$$ A_V = โ€“ R_C \Delta I_C / R_B \Delta I_B $$
$$ = โ€“ ฮฒ {ac}(R_C /R_B ) $$ where $ฮฒ {ac}$ is equal to $ \Delta I_C/\Delta I_B$ from . Thus the linear portion of the active region of the transistor can be exploited for the use in amplifiers.

Example 14.9 In below Fig. , the $V_{BB}$ supply can be varied from 0V to 5.0 V. The Si transistor has $ ฮฒ {dc}$ = 250 and$ R_B$= 100 k ฮฉ, $R_C$= 1 K ฮฉ,VCC = 5.0V. Assume that when the transistor is saturated, $V{CE}$ = 0V and $V_{BE}$ = 0.8V. Calculate (a) the minimum base current, for which the transistor will reach saturation. Hence, (b) determine $V_1$ when the transistor is โ€˜switched onโ€™. (c) find the ranges of $V_1$ for which the transistor is โ€˜switched offโ€™ and โ€˜switched onโ€™.

Solution
Given at saturation $V_{CE}$ = 0V, $V_{BE}$ = 0.8V
$$ V_{CE} = V_{CC} โ€“ I_CR_C $$
$$ I_C = V_{CC}/R_C = 5.0V/1.0k ฮฉ = 5.0 mA $$
Therefore $I_B= I_C/ ฮฒ = 5.0 mA/250 = 20ฮผA
The input voltage at which the transistor will go into saturation is given by
$$ V_{IH} = V_{BB} = I_BR_B +V_{BE} $$
= 20ฮผA ร— 100 k ฮฉ + 0.8V = 2.8V
The value of input voltage below which the transistor remains cutoff is given by
$ V_{IL} = 0.6V $, $ V_{IH} = 2.8V $
Between 0.0V and 0.6V, the transistor will be in the โ€˜switched offโ€™ state. Between 2.8V and 5.0V, it will be in โ€˜switched onโ€™ state.
Note that the transistor is in active state when $I_B$ varies from 0.0mA to 20mA. In this range, $I_C = ฮฒ I_B$ is valid. In the saturation range, $I_C \leq ฮฒ I_B$.

Example 14.10 For a CE transistor amplifier, the audio signal voltage across the collector resistance of 2.0 k ฮฉ is 2.0 V. Suppose the current amplification factor of the transistor is 100, What should be the value of $R_B$ in series with $V_{BB} $ supply of 2.0 V if the dc base current has to be 10 times the signal current. Also calculate the dc drop across the collector resistance. (Refer to Fig. 14.33).

Solution The output ac voltage is 2.0 V. So, the ac collector current $i_C$ = 2.0/2000 = 1.0 mA. The signal current through the base is, therefore given by $i_B = i_C / ฮฒ = 1.0 mA/100 = 0.010 mA. The dc base current has to be 10ร— 0.010 = 0.10 mA.
From Eq.14.16, $ R_B= (V_{BB}- V_{BE}) /I_B$ .Assuming $V_{BE} $= 0.6 V, $R_B $ = (2.0 โ€“ 0.6 )/0.10 = 14 k ฮฉ.
The dc collector current $I_C$= 100ร—0.10 = 10 mA.

14.9.5 Feedback amplifier and transistor oscillator

Fig 14.41 (a) Principle of a transistor amplifier with positive feedback working as an oscillator (b) Tuned collector oscillator (c) Rise and fall (or built up) of current $I_c$ and $I_e$ due to the inductive coupling
  • In an amplifier, a sinusoidal input is given which appears as an amplified signal in the output. This means that an external input is necessary to sustain ac signal in the output for an amplifier.
  • In an oscillator, we get ac output without any external input signal. The output in an oscillator is self-sustained.
  • To attain this, an amplifier is taken. A portion of the output power is returned back to the input in phase with the starting power.
  • The feedback can be achieved by inductive coupling (through mutual inductance) or LC or RC networks.
  • For understanding the oscillator action, we consider the circuit shown in figure b in which the feedback is accomplished by inductive coupling from one coil winding ($T_1$) to another coil winding ($T_2$).
  • As in an amplifier, the base-emitter junction is forward biased while the base-collector junction is reverse biased.
  • We will now analyse how oscillations are built. Suppose switch $S_1$ is put on to apply proper bias for the first time. A surge of collector current flows in the transistor.
  • This current flows through the coil $T_2$ where terminals are numbered 3 and 4 as shown in figure b.
  • This current does not reach full amplitude instantaneously but increases from X to Y, as shown in figure c.
  • The inductive coupling between coil $T_2$ and coil $T_1$ now causes a current to flow in the emitter circuit.
  • As a result of this positive feedback, this current also increases from Xยด to Yยด as shown in figure c.
  • The current in $T_2$ connected in the collector circuit acquires the value Y when the transistor becomes saturated. This means that maximum collector current is flowing and can increase no further.
  • Since there is no further change in collector current, the magnetic field around $T_2$ ceases to grow. As soon as the field becomes static, there will be no further feedback from $T_2$ to $T_1$.
  • Without continued feedback, the emitter current begins to fall. Consequently, collector current decreases from Y towards Z as shown in figure c.
  • However, a decrease of collector current causes the magnetic field to decay around the coil $T_2$.
  • Thus, $T_1$ is now seeing a decaying field in $T_2$.
  • This causes a further decrease in the emitter current till it reaches Zโ€™ when the transistor is cut-off.
  • This means that both $I_E$ and $I_C$ cease to flow.
  • Therefore, the transistor has reverted back to its original state. The whole process now repeats itself.
  • The time for change from saturation to cut-off and back is determined by the constants of the tank circuit or tuned circuit.
  • The resonance frequency (n) of this tuned circuit determines the frequency at which the oscillator will oscillate.
    $$ ฮฝ = \frac {1}{2 \pi \sqrt {LC}} $$
    In the circuit of figure b, the tank or tuned circuit is connected in the collector side. Hence, it is known as tuned collector oscillator. If the tuned circuit is on the base side, it will be known as tuned base oscillator.

Questions for section 14.9

1. What is transistor? Mention its types.

2. Draw neat figures and structures of n-p-n and p-n-p transistors with labelling.

3. Explain in brief the working of n-p-n transistor.

4. Explain in brief the working of p-n-p transistor.

5. Mention the possible transistor configurations.

6. What are the input and output characteristics of common emitter transistor.

7. Define cut-off and active region.

8. How can transistor be used as a switch?

9. How can transistor be used as an amplifier?

10. What are oscillators? State some of the essentials of transistor oscillator.

11. What is feedback amplifier and transistor oscillator.

14.10 Digital electronics and logic gates

The branches of electronics are divided into 2 categories.

1. Analogue

2. Digital

In analogue electronics, analogue signals are used. The data is represented by the binary numbers 0 and 1 using electrical signal called the digital signal.

The digital system has advantage over the analogue system. This is why it is used on a larger scale when compared to the analogue system. These advantages are:

  • It is easy to design and manipulate.
  • The accuracy is greater than the analogue system.
  • These are less affected by noise.
  • The storage of information is easier.

Boolean algebra
In the year 1854, George Boole, an English mathematician developed a mathematical system of logic which can be expressed by truth functions as symbols and then manipulate these symbols to arrive at a logical conclusion. This system is called Boolean algebra.

Logical gates
It is an electronic circuit which makes logical decisions. A logical gate is a digital circuit that is designed for performing particular logical operation as it works according to some logical relationship between input and output voltages. So it is generally known as logic gate.

Some of the popular logical gates are: OR, AND, NOT, NOR, NAND, X-OR, X-NOR gates.
Amongst these, OR, AND and NOT gates are called basic or fundamental gates. They have two or more inputs and only one output.

*** note that NOT gate has only one input.

Each gate has a distant logic symbol and its operation can be described by means of algebraic function and truth tables.

A truth table of a logic gate is a list of its output for different input combinations.

1. NOT gate

The logical symbol of NOT gate is represented as:

Fig 14.42The logic operation of NOT gate is summarized in the truth table given below.

INPUTOUTPUT
AY
01
10

This is the most basic gate, with one input and one output. It produces a โ€˜1โ€™ output if the input is โ€˜0โ€™ and vice-versa. That is, it produces an inverted version of the input at its output. This is why it is also known as an inverter.

2. OR gate

The logical symbol of OR gate is represented as:

Fig 14.43 The logic operation of OR gate is summarized in the truth table given below.

An OR gate has two or more inputs with one output. The output Y is 1 when either input A or input B or both are 1s, that is, if any of the input is high, the output is high.

Apart from carrying out the above mathematical logic operation, this gate can be used for modifying the pulse waveform.

3. AND gate

The logical representation of AND gate is written as:

Fig 14.44 The logical operation of AND gate is summarized in the truth table given below

INPUTOUTPUT
ABY
000
010
100
111

An AND gate has two or more inputs and one output. The output Y of AND gate is 1 only when input A and input B are both 1.

4. NAND gate

The logical symbol of NAND symbol can be written as

Fig 14.45 The logical operation of NAND gate is summarized in the table given below.

INPUTOUTPUT
ABY
001
011
101
110

This is an AND gate followed by a NOT gate. If inputs A and B are both โ€˜1โ€™, the output Y is not โ€˜1โ€™. The gate gets its name from this NOT AND behaviour. NAND gates are also called Universal Gates since by using these gates you can realise other basic gates like OR, AND and NOT.

5. NOR gate

The logical symbol of NOR gate is written as follows

Fig 14.46 The logical operation of NOR gate is summarized in the truth table given below.

INPUTOUTPUT
ABY
001
010
100
110

It has two or more inputs and one output. A NOT- operation applied after OR gate gives a NOT-OR gate (or simply NOR gate). Its output Y is โ€˜1โ€™ only when both inputs A and B are โ€˜0โ€™, i.e., neither one input nor the other is โ€˜1โ€™.

NOR gates are considered as universal gates because we can obtain all the gates like AND, OR, NOT by using only NOR gates.

Example 14.11 Justify the output waveform (Y) of the OR gate for the following inputs A and B given in Fig. 14.37.

Solution:

Note the following:

At t < $ t_1$; $\space$ A = 0, B = 0; $ \hspace{10mm} $Hence Y = 0 For $t_1$ to $t_2$; $ \space $ A = 1, B = 0; $ \hspace{10mm} $Hence Y = 1 For $t_2$ to $t_3$; $ \space $ A = 1, B = 1; $ \hspace{10mm} $ Hence Y = 1 For $t_3$ to $t_4$; $ \space $ A = 0, B = 1; $ \hspace{10mm} $ Hence Y = 1 For $t_4$ to $t_5$; $ \space $ A = 0, B = 0; $\hspace{10mm} $ Hence Y = 0 For $t_5$ to $t_6$; $ \space $ A = 1, B = 0; $ \hspace{10mm} $ Hence Y = 1 For t > $t_6$ ;$ \space $ A = 0, B = 1; $ \hspace{10mm} $Hence Y = 1
Therefore the waveform Y will be as shown in the Fig. 14.47.

Fig 14.47

Example 14.12 Take A and B input waveforms similar to that in Example 14.11. Sketch the output waveform obtained from AND gate.

Solution

  • For t $\leq$ $t_1$; $ \hspace{10mm}$A = 0, B = 0; $ \hspace{10mm}$Hence Y = 0
  • For $t_1$ to $t_2$; $ \hspace{10mm}$A = 1, B = 0; $\hspace{10mm} $Hence Y = 0
  • For $t_2$ to $t_3$; $ \hspace{10mm} $A = 1, B = 1;$\hspace{10mm} $ Hence Y = 1
  • For $t_3$ to $t_4$; $\hspace{10mm} $A = 0, B = 1; $\hspace{10mm} $Hence Y = 0
  • For $t_4$ to $t_5$; \hspace{10mm} $A = 0, B = 0; $\hspace{10mm} $ Hence Y = 0
  • For $t_5$ to $t_6$; $ \hspace{10mm}$A = 1, B = 0; $ \hspace{10mm} $Hence Y = 0
  • For t > $t_6$; $ \hspace{10mm} $A = 0, B = 1; $\hspace{10mm} $Hence Y = 0
    Based on the above, the output waveform for AND gate can be drawn as given below.
Fig 14.48

Example 14.13 Sketch the output Y from a NAND gate having inputs A and B given below:

Solution

  • For t < $t_1$; $ \hspace{10mm} $ A = 1, B = 1; $ \hspace{10mm} $ Hence Y = 0
  • For $t_1$to $t_2$; $\hspace{10mm} $ A = 0, B = 0; $ \hspace{10mm} $Hence Y = 1
  • For $t_2$ to $t_3$; $ \hspace{10mm} $ A = 0, B = 1; $ \hspace{10mm } $ Hence Y = 1
  • For $t_34 to $t_4$; $ \hspace{10mm} $ A = 1, B = 0; $ \hspace{10mm} $Hence Y = 1
  • For $t_4$ to $t_5$; $ \hspace{10mm} $ A = 1, B = 1;$ \hspace{10mm} $ Hence Y = 0
  • For $t_5$ to $t_6$; $ \hspace {10mm} $ A = 0, B = 0; $ \hspace{10mm} $Hence Y = 1
  • For t > $t_6$; $ \hspace{10mm} $ A = 0, B = 1; $ \hspace{10mm} $Hence Y = 1
Fig 14.49

Questions for section 14.10

1. Give the logical symbol and truth table for the following gates:

I. NOT gate

II. OR gate

III. AND gate

IV. NAND gate

V. NOR gate

14.11 Integrated circuits

  • The conventional method of making circuits is to choose components like diodes, transistor, R, L, C etc., and connect them by soldering wires in the desired manner.
  • Apart from this, such circuits were less reliable and less shock proof.
  • The concept of fabricating an entire circuit on a small single block (or chip) of a semiconductor has revolutionised the electronics technology. Such a circuit is known as Integrated Circuit (IC).
  • The most widely used technology is the Monolithic Integrated Circuit.
Fig 14.50 The casing and connection of a โ€˜chipโ€™
  • The entire circuit is formed on a single silicon crystal (or chip). The chip dimensions are as small as 1mm ร— 1mm or it could even be smaller.
  • Depending on nature of input signals, ICโ€™s can be grouped in two categories: (a) linear or analogue ICโ€™s and (b) digital ICโ€™s. The linear ICโ€™s process analogue signals which change smoothly and continuously over a range of values between a maximum and a minimum.
  • The output is more or less directly proportional to the input, i.e., it varies linearly with the input.
  • One of the most useful linear ICโ€™s is the operational amplifier.

Questions or section 14.11

  1. What are integrated circuits?
  2. What is monolithic integrated circuit?
  3. Give the dimensions of the ideal silicon crystal or the chip.