SECTION – A
26. Given below are two statements:
Statement I: In a vernier callipers, one vernier scale division is always smaller than one main scale division.
Statement II: The vernier constant is given by one main scale division multiplied by the number of vernier scale division.
In the light of the above statements, choose the correct answer from the options given below.
(1) Both Statement I and Statement II are false.
(2) Statement I is true but Statement II is false.
(3) Both Statement I and Statement II are true.
(4) Statement I is false but Statement II is true.
Answer: (2)
Solution:
Statement I: In a vernier callipers, one vernier scale division is always smaller than one main scale division.
In a standard Vernier calliper, the Vernier Scale is designed so that $n$ divisions on the vernier scale ($VSD$) coincide with $(n-1)$ divisions on the Main Scale ($MSD$).
Mathematically, this relationship is expressed as:
$$n \times VSD = (n-1) \times MSD$$
Rearranging for one $VSD$:
$$1 \text{ VSD} = \left(\frac{n-1}{n}\right) \times MSD$$
Since $\frac{n-1}{n}$ is always less than 1, it follows that $\mathbf{1 \text{ VSD} < 1 \text{ MSD}}$. This configuration allows the instrument to measure lengths with greater precision than the main scale alone. While specialized “retrograde” verniers exist where the $VSD$ is larger, in the context of standard physics and competitive exams, Statement I is considered True.
Statement II: The vernier constant is given by one main scale division multiplied by the number of vernier scale division.
The Vernier Constant (VC), also known as the Least Count (LC), is the smallest value that can be measured by the instrument. It is defined as the difference between the value of one main scale division and one vernier scale division.
$$VC = 1 \text{ MSD} – 1 \text{ VSD}$$
Using the relationship $1 \text{ VSD} = \left(\frac{n-1}{n}\right) \text{ MSD}$, we can substitute:
$$VC = 1 \text{ MSD} – \left(\frac{n-1}{n}\right) \text{ MSD}$$
$$VC = 1 \text{ MSD} \times \left(1 – \frac{n-1}{n}\right)$$
$$VC = \frac{1 \text{ MSD}}{n}$$
Where $n$ is the number of divisions on the vernier scale. Therefore, the Vernier Constant is calculated by dividing the value of one main scale division by the total number of vernier divisions, not by multiplying them.
Statement II is False.
Conclusion
- Statement I is True.
- Statement II is False.
The correct choice is option (2).
27. A line charge of length $\frac{a}{2}$ is kept at the center of an edge BC of a cube ABCDEFGH having edge length ‘$a$’ as shown in the figure. If the density of line is $\lambda$ C per unit length, then the total electric flux through all the faces of the cube will be ____. (Take $\epsilon_0$ as the free space permittivity)

(1) $\frac{\lambda a}{8 \epsilon_0}$
(2) $\frac{\lambda a}{16 \epsilon_0}$
(3) $\frac{\lambda a}{2 \epsilon_0}$
(4) $\frac{\lambda a}{4 \epsilon_0}$
Answer: (1)
Solution:
1. Understanding Gaussโs Law
According to Gaussโs Law, the total electric flux ($\phi$) through any closed surface is equal to the net charge enclosed ($q_{in}$) divided by the permittivity of free space ($\epsilon_0$):
$$\phi = \frac{q_{in}}{\epsilon_0}$$
2. Determining the Enclosed Charge
The key to this problem is realizing that the line charge is located on the edge of the cube. An edge in a cubic structure is shared by exactly four identical cubes.
Total Charge of the Line: Since the length of the line charge is $\frac{a}{2}$ and the density is $\lambda$, the total charge is:
$$Q_{total} = \lambda \times \frac{a}{2} = \frac{\lambda a}{2}$$
Charge Inside One Cube: Because the edge is shared equally by four cubes, only one-fourth of the charge on that edge is considered “inside” the volume of the specific cube $ABCDEFGH$.
$$q_{in} = \frac{1}{4} \times Q_{total} = \frac{1}{4} \times \left( \frac{\lambda a}{2} \right) = \frac{\lambda a}{8}$$
3. Calculating Total Flux
Now, applying the values to the Gaussโs Law formula:
$$\phi = \frac{\frac{\lambda a}{8}}{\epsilon_0}$$
$$\phi = \frac{\lambda a}{8 \epsilon_0}$$
Conclusion
The total electric flux through all the faces of the cube is $\mathbf{\frac{\lambda a}{8 \epsilon_0}}$. This corresponds to option (1).
28.
Sliding contact of a potentiometer is in the middle of the potentiometer wire having resistance $R_p = 1\Omega$ as shown in the figure. An external resistance of $R_e = 2\Omega$ is connected via the sliding contact.
(1) 0.3 A
(2) 1.35 A
(3) 1.0 A
(4) 0.9 A
Answer: (3)
29. Given below are two statements: one is labelled as Assertion (A) and the other is labelled as Reason (R).
Assertion (A): If Youngโs double slit experiment is performed in an optically denser medium than air, then the consecutive fringes come closer.
Reason (R): The speed of light reduces in an optically denser medium than air while its frequency does not change.
In the light of the above statements, choose the most appropriate answer from the options given below:
(1) Both (1) and (R) are true and (R) is the correct explanation of (1)
(2) (1) is false but (R) is true.
(3) Both (1) and (R) are true but (R) is not the correct explanation of (1)
(4) (1) is true but (R) is false.
Answer: (1)
Solution:
1. The Reason: Light Behavior in Denser Media
When light travels from air into an optically denser medium (like water or glass):
- Frequency (f): Remains constant. Frequency is a property of the source, not the medium.
- Speed (v): Decreases. By definition, the refractive index $\mu = \frac{c}{v}$. As $\mu$ increases, the speed $v$ must decrease.
- Wavelength ($\mathbf{\lambda}$): Since $v = f \lambda$, and $f$ is constant, a decrease in speed directly results in a decrease in wavelength.
Specifically, the wavelength in a medium ($\lambda_{med}$) is related to the wavelength in a vacuum ($\lambda_{air}$) by:
$$\lambda_{med} = \frac{\lambda_{air}}{\mu}$$
Therefore, the Reason (R) is a scientifically accurate statement.
2. The Assertion: Effect on Fringe Width
In Youngโs Double Slit Experiment, the distance between two consecutive bright or dark fringes is called the Fringe Width ($\mathbf{\beta}$). It is given by the formula:
$$\beta = \frac{\lambda D}{d}$$
Where:
- $\lambda$ = wavelength of light
- $D$ = distance between the slits and the screen
- $d$ = distance between the two slits
When the apparatus is submerged in a denser medium, $\lambda$ decreases to $\lambda / \mu$. Consequently, the new fringe width becomes:
$$\beta_{med} = \frac{\lambda_{med} D}{d} = \frac{\beta_{air}}{\mu}$$
Since $\mu > 1$, the fringe width decreases ($\beta_{med} < \beta_{air}$). A smaller fringe width means the fringes are packed more tightly, or they come closer. Thus, the Assertion (A) is also true.
Final Relationship
The Reason explains why the wavelength changes, which is the direct cause of the change in fringe width described in the Assertion.
Assertion (A): True
Reason (R): True
Connection: (R) is the correct explanation of (A).
30. Two spherical bodies of same materials having radii 0.2 m and 0.8 m are placed in same atmosphere. The temperature of the smaller body is 800 K and temperature of bigger body is 400 K. If the energy radiate from the smaller body is E, the energy radiated from the bigger body is (assume, effect of the surrounding to be negligible)
(1) 256 E
(2) E
(3) 64 E
(4) 16 E
Answer: (2)
Solution:
We are comparing two spherical bodies made of the same material:
- Smaller Body: Radius $r_1 = 0.2\text{ m}$, Temperature $T_1 = 800\text{ K}$, Energy Radiated $= E$.
- Bigger Body: Radius $r_2 = 0.8\text{ m}$, Temperature $T_2 = 400\text{ K}$, Energy Radiated $=?$
1. The Stefan-Boltzmann Law
The total energy radiated per unit time (Power, $P$) by a black body is given by the Stefan-Boltzmann Law:
$$P = \sigma e A T^4$$
Where:
- $\sigma$ is the Stefan-Boltzmann constant.
- $e$ is the emissivity (same for both bodies as they are the same material).
- $A$ is the surface area of the sphere ($4\pi r^2$).
- $T$ is the absolute temperature in Kelvin.
2. Establishing the Proportionality
Since $\sigma$, $e$, and $4\pi$ are constants for both bodies, we can say that the radiated energy $E$ is proportional to the square of the radius and the fourth power of the temperature:
$$E \propto r^2 T^4$$
3. Comparing the Two Bodies
Let $E_1$ be the energy of the smaller body and $E_2$ be the energy of the larger body. We can set up a ratio:
$$\frac{E_2}{E_1} = \left( \frac{r_2}{r_1} \right)^2 \times \left( \frac{T_2}{T_1} \right)^4$$
Substitute the given values:
$$\frac{E_2}{E} = \left( \frac{0.8}{0.2} \right)^2 \times \left( \frac{400}{800} \right)^4$$
Simplify the terms:
- $\frac{0.8}{0.2} = 4$
- $\frac{400}{800} = \frac{1}{2}$
$$\frac{E_2}{E} = (4)^2 \times \left( \frac{1}{2} \right)^4$$
$$\frac{E_2}{E} = 16 \times \frac{1}{16}$$
$$\frac{E_2}{E} = 1$$
The calculation shows that $E_2 = E$. Even though the larger body has a much greater surface area, its lower temperature (being half that of the smaller body) reduces the radiation intensity significantly because radiation depends on the fourth power of temperature.
The energy radiated from the bigger body is E, which corresponds to option (2).
31. An amount of ice of mass $10^{-3}$ kg and temperature $-10^{\circ}\text{C}$ is transformed to vapour of temperature $110^{\circ}$ by applying heat. The total amount of work required for this conversion is,
(Take, specific heat of ice = $2100\text{ Jkg}^{-1}\text{K}^{-1}$, specific heat of water = $4180\text{ Jkg}^{-1}\text{K}^{-1}$, specific heat of steam = $1920\text{ Jkg}^{-1}\text{K}^{-1}$, Latent heat of ice = $3.35 \times 10^5\text{ Jkg}^{-1}$ and Latent heat of steam = $2.25 \times 10^6\text{ Jkg}^{-1}$)
(1) 3022 J
(2) 3043 J
(3) 3003 J
(4) 3024 J
Answer: (2)
Solution:
Step 1: Heating Ice from $\mathbf{-10^{\circ}}C$ to $\mathbf{0^{\circ}C}$
In this stage, the temperature of the ice increases. We use the formula $Q = m \cdot s_{ice} \cdot \Delta T$.
- $m = 10^{-3} \text{ kg}$
- $s_{ice} = 2100 \text{ Jkg}^{-1}\text{K}^{-1}$
- $\Delta T = 0 – (-10) = 10ยฐC$
- $Q_1 = 10^{-3} \times 2100 \times 10 = \mathbf{21 \text{ J}}$
Step 2: Melting Ice at $\mathbf{0^{\circ}}C$ to Water at $\mathbf{0ยฐC$
This is a phase change where temperature remains constant. We use the Latent Heat of Fusion ($L_f$).
- $L_f = 3.35 \times 10^5 \text{ Jkg}^{-1}$
- $Q_2 = m \cdot L_f = 10^{-3} \times 3.35 \times 10^5 = \mathbf{335 \text{ J}}$
Step 3: Heating Water from $0ยฐC$ to $100ยฐC$
The temperature of the liquid water increases to its boiling point.
- $s_{water} = 4180 \text{ Jkg}^{-1}\text{K}^{-1}$
- $\Delta T = 100 – 0 = 100ยฐC$
- $Q_3 = 10^{-3} \times 4180 \times 100 = \mathbf{418 \text{ J}}$
Step 4: Converting Water at $\mathbf{100^{\circ}C}$ to Steam at $\mathbf{100^{\circ}C}$
This is a phase change from liquid to gas. We use the Latent Heat of Vaporization ($L_v$).
- $L_v = 2.25 \times 10^6 \text{ Jkg}^{-1}$
- $Q_4 = m \cdot L_v = 10^{-3} \times 2.25 \times 10^6 = \mathbf{2250 \text{ J}}$
Step 5: Heating Steam from $\mathbf{100^{\circ}C}$ to $\mathbf{110^{\circ}C}$
The temperature of the steam increases further.
$s_{steam} = 1920 \text{ Jkg}^{-1}\text{K}^{-1}$
$\Delta T = 110 – 100 = 10ยฐC$
$Q_5 = 10^{-3} \times 1920 \times 10 = \mathbf{19.2 \text{ J}}$
Total Work Required
To find the total energy, we sum all the individual components:
$$Q_{total} = Q_1 + Q_2 + Q_3 + Q_4 + Q_5$$
$$Q_{total} = 21 + 335 + 418 + 2250 + 19.2 = \mathbf{3043.2 \text{ J}}$$
Rounding to the nearest whole number as per the options, the total work required is 3043 J, which matches option (2).
32. An electron in the ground state of the hydrogen atom has the orbital radius of $5.3 \times 10^{โ11}m$ while that for the electron in third excited state is $8.48 \times 10^{โ10}m$. The ratio of the de Broglie wavelengths of electron in the ground state to that in excited state is
(1) 4
(2) 9
(3) 3
(4) 16
Answer: (1)
Solution:
1. Understanding the Quantum States
Ground State: This is the first energy level, so $n_1 = 1$.
Third Excited State: The “excited state” count starts after the ground state.
- 1st excited state $\rightarrow n = 2$
- 2nd excited state $\rightarrow n = 3$
- 3rd excited state $\mathbf{\rightarrow n_4 = 4}$
2. Deriving the Relationship
According to Bohr’s second postulate, the angular momentum of an electron is quantized:
$$mvr = \frac{nh}{2\pi}$$
From this, we can express the momentum ($mv$) as:
$$mv = \frac{nh}{2\pi r}$$
Now, we substitute this into the de Broglie wavelength formula ($\lambda = \frac{h}{mv}$):
$$\lambda = \frac{h}{\left(\frac{nh}{2\pi r}\right)}$$
$$\lambda = \frac{2\pi r}{n}$$
This result tells us that the circumference of the orbit ($2\pi r$) must be an integral multiple of the de Broglie wavelength. More importantly, it shows the proportionality:
$$\lambda \propto \frac{r}{n}$$
3. Calculating the Ratio
We need the ratio of the wavelength in the ground state ($\lambda_1$) to the wavelength in the third excited state ($\lambda_4$):
$$\frac{\lambda_1}{\lambda_4} = \frac{r_1 / n_1}{r_4 / n_4} = \left(\frac{r_1}{r_4}\right) \times \left(\frac{n_4}{n_1}\right)$$
Given Values:
$r_1 = 5.3 \times 10^{-11} \text{ m}$
$r_4 = 8.48 \times 10^{-10} \text{ m}$ (which is $84.8 \times 10^{-11} \text{ m}$)
$n_1 = 1$
$n_4 = 4$
Substitution:
$$\frac{\lambda_1}{\lambda_4} = \left(\frac{5.3 \times 10^{-11}}{84.8 \times 10^{-11}}\right) \times \left(\frac{4}{1}\right)$$
$$\frac{\lambda_1}{\lambda_4} = \left(\frac{5.3}{84.8}\right) \times 4$$
Since $84.8 \div 5.3 = 16$:
$$\frac{\lambda_1}{\lambda_4} = \frac{1}{16} \times 4 = \frac{4}{16} = \frac{1}{4}$$
The ratio of the de Broglie wavelength in the ground state to that in the third excited state is 1:4. Looking at the provided options, they represent the factor of change or the reciprocal ratio depending on the question’s phrasing “ratio of… to…”. Based on the logic of the calculation, the wavelength in the excited state is 4 times larger than in the ground state.
Thus, correct answer is option (1) 4.
33. In the diagram given below, there are three lenses formed. Considering negligible thickness of each of them as compared to $[R_1]$ and $[R_2]$, ie., the radii of curvature for upper and lower surfaces of the glass lens, the power of the combination is

(1) $-\frac{1}{6}\left( \frac{1}{|R_1|} + \frac{1}{|R_2|} \right)$
(2) $-\frac{1}{6}\left( \frac{1}{|R_1|} – \frac{1}{|R_2|} \right)$
(3) $\frac{1}{6}\left( \frac{1}{|R_1|} + \frac{1}{|R_2|} \right)$
(4) $\frac{1}{6}\left( \frac{1}{|R_1|} – \frac{1}{|R_2|} \right)$
Answer: (2)
34. An electron is made to enters symmetrically between two parallel and equally but oppositely charged metal plates, each of 10 cm length. The electron emerges out of the field region with a horizontal component of velocity $10^6 m/s$. If the magnitude of the electric between the plates is 9.1 V/cm, then the vertical component of velocity of electron is
(mass of electron $= 9.1 \times 10^{โ31}kg$ and charge of electron $= 1.6 \times 10^{โ19}C)$
(1) $1 \times 10^6 m/s$
(2) $0$
(3) $16 \times 10^6 m/s$
(4) $16 \times 10^4 m/s$
Answer: (3)
Solution:
1. Analyze the Motion
The electron’s motion is similar to projectile motion, where horizontal and vertical components are independent:
Horizontal Motion: There is no force in the horizontal direction, so the horizontal velocity ($v_x$) remains constant at $10^6 \text{ m/s}$.
Vertical Motion: The electric field ($E$) between the plates exerts a constant force, causing vertical acceleration ($a_y$).
2. Calculate Time Spent in the Field
The time ($t$) the electron spends between the plates depends on the plate length ($L$) and the horizontal speed:
Length $L = 10 \text{ cm} = 0.1 \text{ m}$
Horizontal velocity $v_x = 10^6 \text{ m/s}$

$$t = \frac{L}{v_x} = \frac{0.1}{10^6} = 10^{-7} \text{ seconds}$$
3. Determine Vertical Acceleration
The vertical force is $F = qE$. According to Newton’s Second Law ($F = ma$):
Electric Field $E = 9.1 \text{ V/cm} = 910 \text{ V/m}$
Charge of electron $e = 1.6 \times 10^{-19} \text{ C}$
Mass of electron $m = 9.1 \times 10^{-31} \text{ kg}$
$$a_y = \frac{eE}{m} = \frac{(1.6 \times 10^{-19}) \times 910}{9.1 \times 10^{-31}}$$
$$a_y = \frac{1.6 \times 91 \times 10^{-18}}{9.1 \times 10^{-31}} = 1.6 \times 10^{14} \text{ m/s}^2$$
4. Calculate Final Vertical Velocity
Since the electron enters “symmetrically” (horizontally), its initial vertical velocity $u_y = 0$. Using the first equation of motion:
$$v_y = u_y + a_yt$$
$$v_y = 0 + (1.6 \times 10^{14}) \times (10^{-7})$$
$$v_y = 1.6 \times 10^7 \text{ m/s}$$
To match the format in the options:
$$v_y = 16 \times 10^6 \text{ m/s}$$
The vertical component of the velocity of the electron is $\mathbf{16 \times 10^6 \text{ m/s}}$, which corresponds to option (3).
35. Which of the following resistivity ($\rho$) v/s temperature (T) curves is most suitable to be used in wire bound standard resistors?
(1)
(2)
(3)
(4)
Answer: (1)
Solution:
1. Requirements for Standard Resistors
A standard resistor is designed to provide a constant and reliable resistance value. For this to happen, the material used must have a very low temperature coefficient of resistance. This means that as the temperature changes (due to the environment or the current passing through it), the resistance should ideally remain nearly unchanged.
2. Material Selection
Wire-bound resistors are typically made from alloys like Manganin or Constantan. These alloys are chosen specifically because their resistivity ($\rho$) is almost independent of temperature over a wide range.
3. Analyzing the Curves
Curve (1): Shows a nearly horizontal line (or a very slight linear increase). This represents a material where resistivity has a very weak dependence on temperature. This is the ideal characteristic for a standard resistor because it ensures stability.
Curve (2): Shows an exponential increase in resistivity with temperature. This is typical of pure metals like Copper or Aluminum at high temperatures, which would make the resistance fluctuate too much for standard use.
Curve (3): Shows resistivity decreasing as temperature increases. This is the characteristic of semiconductors, not the metals used in wire-bound resistors.
Curve (4): Shows a sharp linear decrease, which does not represent the behavior of standard resistive alloys.
Since wire-bound standard resistors require a material whose resistivity remains stable despite temperature fluctuations, Curve (1) is the most suitable representation. This corresponds to option (1).
36. A closed organ and an open organ tube filled by two different gases having same bulk modulus but different densities $\rho_1$ and $\rho_2$ respectively. The frequency of $9^{\text{th}}$ harmonic of closed tube is identical with $4^{\text{th}}$ harmonic of open tube. If the length of the closed tube is $10\text{ cm}$ and the density ratio of the gases is $\rho_1: \rho_2 = 1: 16$, then the length of the open tube is:
(1) $\frac{20}{7}\text{ cm}$
(2) $\frac{15}{7}\text{ cm}$
(3) $\frac{20}{9}\text{ cm}$
(4) $\frac{15}{9}\text{ cm}$
Answer: (3)
Solution:
1. Fundamental Formulas for Frequency
The frequency of a sound wave in a tube depends on the speed of sound ($v$) and the length of the tube ($L$).
Closed Organ Tube: Produces only odd harmonics ($1, 3, 5, 7, 9…$).
The frequency of the $n^{th}$ harmonic is: $f_c = \frac{n v_1}{4 L_c}$
Open Organ Tube: Produces all harmonics ($1, 2, 3, 4…$).
The frequency of the $m^{th}$ harmonic is: $f_o = \frac{m v_2}{2 L_o}$
2. Speed of Sound in Gases
The speed of sound in a gas is given by the formula:
$$v = \sqrt{\frac{B}{\rho}}$$
Where $B$ is the bulk modulus and $\rho$ is the density.
Since both gases have the same bulk modulus (B), the speeds are:
$v_1 = \sqrt{\frac{B}{\rho_1}}$
$v_2 = \sqrt{\frac{B}{\rho_2}}$
3. Setting up the Equation
The problem states that the 9th harmonic of the closed tube is identical to the 4th harmonic of the open tube.
$$f_c (\text{9th harmonic}) = f_o (\text{4th harmonic})$$
$$\frac{9 v_1}{4 L_c} = \frac{4 v_2}{2 L_o}$$
Simplify the right side:
$$\frac{9 v_1}{4 L_c} = \frac{2 v_2}{L_o}$$
4. Substituting Speed and Density
Now, substitute the expressions for $v_1$ and $v_2$:
$$\frac{9}{4 L_c} \sqrt{\frac{B}{\rho_1}} = \frac{2}{L_o} \sqrt{\frac{B}{\rho_2}}$$
Cancel out $\sqrt{B}$ and rearrange to solve for the length of the open tube ($L_o$):
$$\frac{L_o}{L_c} = \frac{2 \times 4}{9} \times \frac{\sqrt{B/\rho_2}}{\sqrt{B/\rho_1}}$$
$$\frac{L_o}{L_c} = \frac{8}{9} \times \sqrt{\frac{\rho_1}{\rho_2}}$$
5. Final Calculation
Given data:
$L_c = 10 \text{ cm}$
$\rho_1: \rho_2 = 1: 16$, so $\sqrt{\frac{\rho_1}{\rho_2}} = \sqrt{\frac{1}{16}} = \frac{1}{4}$
Substitute these into our ratio:
$$\frac{L_o}{10} = \frac{8}{9} \times \frac{1}{4}$$
$$\frac{L_o}{10} = \frac{2}{9}$$
$$L_o = \frac{2 \times 10}{9} = \frac{20}{9} \text{ cm}$$
The length of the open tube is $\mathbf{\frac{20}{9} \text{ cm}}$.
37. A uniform circular disc of radius โRโ and mass โMโ is rotating about an axis perpendicular to its plane and passing through its centre. A small circular part of radius R/2 is removed from the original disc as shown in the figure. Find the moment of inertia of the remaining part of the original disc about the axis as given above.

(1) $\frac{7}{32} \text{MR}^2$
(2) $\frac{9}{32} \text{MR}^2$
(3) $\frac{17}{32} \text{MR}^2$
(4) $\frac{13}{32} \text{MR}^2$
Answer: (4)
Solution:
1. Properties of the Original and Removed Discs
First, let’s find the mass of the small disc that was removed. Since the disc is uniform, its mass is proportional to its area.
- Area of original disc: $A_1 = \pi R^2$ (Mass = $M$)
- Area of removed disc: $A_2 = \pi \left(\frac{R}{2}\right)^2 = \frac{\pi R^2}{4}$
Since the area is $\frac{1}{4}$ of the original, the mass of the removed part (m) is:
$$m = \frac{M}{4}$$
2. Moment of Inertia of the Original Disc ($\mathbf{I_{total}}$)
The moment of inertia of a full disc about its central axis is:
$$I_{total} = \frac{1}{2} M R^2$$
3. Moment of Inertia of the Removed Part ($\mathbf{I_{removed}}$)
The removed disc is not rotating about its own center, but about the center of the original disc. We must use the Parallel Axis Theorem:
$$I = I_{cm} + md^2$$
Moment of inertia about its own center ($\mathbf{I_{cm}}$):
$$I_{cm} = \frac{1}{2} m r^2 = \frac{1}{2} \left(\frac{M}{4}\right) \left(\frac{R}{2}\right)^2 = \frac{MR^2}{32}$$
Distance between centers (d):
Looking at the geometry, the center of the small disc is at a distance $d = \frac{R}{2}$ from the original center.
Shifted Moment of Inertia ($\mathbf{md^2}$):
$$md^2 = \left(\frac{M}{4}\right) \left(\frac{R}{2}\right)^2 = \frac{MR^2}{16}$$
Adding these together for the removed part:
$$I_{removed} = \frac{MR^2}{32} + \frac{MR^2}{16} = \frac{3MR^2}{32}$$
4. Moment of Inertia of the Remaining Part ($\mathbf{I_{rem}}$)
To find the final result, we subtract the moment of inertia of the removed part from the original total:
$$I_{rem} = I_{total} – I_{removed}$$
$$I_{rem} = \frac{MR^2}{2} – \frac{3MR^2}{32}$$
To subtract, we find a common denominator (32):
$$I_{rem} = \frac{16MR^2}{32} – \frac{3MR^2}{32}$$
$$I_{rem} = \frac{13}{32} MR^2$$
The moment of inertia of the remaining part is $\mathbf{\frac{13}{32} MR^2}$, which corresponds to option (4).
38. A small point of mass m is placed at a distance 2R from the centre โOโ of a big uniform solid sphere of mass M and radius R. The gravitational force on โmโ due to M is $F_1$. A spherical part of radius R/3 is removed from the big sphere as shown in the figure and the gravitational force on m due to remaining part of M is found to be $F_2$. The value of ratio $F_1: F_2$ is

(1) 16: 9
(2) 11: 10
(3) 12: 11
(4) 12: 9
Answer: (3)
Solution:
1. Calculation of $\mathbf{F_1}$ (Initial Force)
Initially, we have a complete uniform solid sphere of mass $M$ and radius $R$. A point mass $m$ is placed at a distance $r = 2R$ from the center $O$.
According to Newton’s Law of Gravitation:
$$F_1 = \frac{GMm}{(2R)^2} = \frac{GMm}{4R^2}$$
2. Calculation of $\mathbf{F_2}$ (Force after removal)
When a spherical part is removed, the net force $F_2$ is:
$\mathbf{F_2 = F_1 – F_{removed}}$
i. Mass of the removed part (m’)
The volume of a sphere is proportional to the cube of its radius ($V \propto R^3$). Since the sphere is uniform:
- Radius of original sphere = $R$
- Radius of removed part = $R/3$
- Mass of removed part $m’ = M \times \left( \frac{R/3}{R} \right)^3 = \frac{M}{27}$
ii. Distance of the removed part’s center from m
Looking at the geometry:
- The center of the removed part is at a distance of $R – R/3 = 2R/3$ from the center $O$.
- The point mass $m$ is at $2R$ from center $O$.
- Distance from center of removed cavity to $m$ ($x$) = $2R – \frac{2R}{3} = \frac{4R}{3}$
iii. Force exerted by the removed part ($\mathbf{F_{removed}}$)
$$F_{removed} = \frac{G(m’)m}{x^2} = \frac{G(\frac{M}{27})m}{(\frac{4R}{3})^2}$$
$$F_{removed} = \frac{GMm}{27} \times \frac{9}{16R^2} = \frac{GMm}{48R^2}$$
3. Finding $\mathbf{F_2}$ and the Ratio
Now, subtract the forces:
$$F_2 = \frac{GMm}{4R^2} – \frac{GMm}{48R^2}$$
To solve this, take a common denominator of $48R^2$:
$$F_2 = \frac{12GMm – 1GMm}{48R^2} = \frac{11GMm}{48R^2}$$
Finally, find the ratio $\mathbf{F_1: F_2}$:
$$\frac{F_1}{F_2} = \frac{\frac{GMm}{4R^2}}{\frac{11GMm}{48R^2}} = \frac{1}{4} \times \frac{48}{11} = \frac{12}{11}$$
The ratio $F_1: F_2$ is $\mathbf{12: 11}$, which corresponds to option (3).
39. The work functions of cesium (Cs) and lithium (Li) metals are 1.9 eV and 2.5 eV, respectively. If we incident a light of wavelength 550 nm on these two metal surface, then photo-electric effect is possible for the case of
(1) Li only
(2) Cs only
(3) Neither Cs nor Li
(4) Both Cs and Li
Answer: (2)
Solution:
1. The Condition for Photoelectric Effect
The photoelectric effect occurs only if the energy of the incident photon ($E$) is greater than or equal to the work function ($\phi$) of the metal:
$$E \geq \phi$$
Work Function ($\mathbf{\phi}$): The minimum energy required to eject an electron from the metal surface.
Incident Energy (E): The energy carried by the light hitting the surface.
2. Calculating the Energy of Incident Light
The energy of a photon can be calculated using the wavelength ($\lambda$) with the following convenient formula:
$$E (\text{in eV}) = \frac{1240}{\lambda (\text{in nm})}$$
Given: Wavelength of incident light ($\lambda$) = $550 \text{ nm}$
Calculation:
$$E = \frac{1240}{550} \text{ eV}$$
$$E \approx 2.25 \text{ eV}$$
The energy of each incident photon is approximately 2.25 eV.
3. Comparing with Metal Work Functions
Now, we compare the incident energy (2.25 eV) with the work functions provided:
For Cesium (Cs):
- Work function ($\phi_{Cs}$) = $1.9 \text{ eV}$
- Comparison: $2.25 \text{ eV} > 1.9 \text{ eV}$
- Result: The photon has enough energy to eject electrons. Photoelectric effect is possible.
For Lithium (Li):
- Work function ($\phi_{Li}$) = $2.5 \text{ eV}$
- Comparison: $2.25 \text{ eV} < 2.5 \text{ eV}$
- Result: The photon does not have enough energy to overcome the work function. Photoelectric effect is not possible.
The photoelectric effect will occur for Cesium (Cs) only.
40. If B is magnetic field and $\mu_0$ is permeability of free space, then the dimensions of $(B/\mu_0)$ is
(1) $\text{MT}^{-2}\text{A}^{-1}$
(2) $\text{L}^{-1}\text{A}$
(3) $\text{LT}^{-2}\text{A}^{-1}$
(4) $\text{ML}^2\text{T}^{-2}\text{A}^{-1}$
Answer: (2)
Solution:
1. Identifying a Relevant Physical Relation
The easiest way to find the dimensions of a ratio is to use a standard physical formula where that ratio appears. One such formula is for the magnetic field inside a long solenoid:
$$B = \mu_0 n I$$
Rearranging this to isolate the ratio $\frac{B}{\mu_0}$:
$$\frac{B}{\mu_0} = n I$$
Where:
n is the number of turns per unit length ($n = \frac{N}{L}$).
I is the electric current.
2. Determining Dimensions of the Components
Now, we find the dimensions of the terms on the right side:
Number of turns per unit length ($n$): Since “turns” is a dimensionless number, the dimension of $n$ is simply $\frac{1}{\text{Length}}$.
$$[n] = [L^{-1}]$$
Electric Current ($I$): The standard dimension for current is Ampere ($A$).
$$[I] = [A^1]$$
3. Calculating the Dimensions of $\mathbf{\frac{B}{\mu_0}}$
Multiply the dimensions together:
$$\left[ \frac{B}{\mu_0} \right] = [n] \times [I]$$
$$\left[ \frac{B}{\mu_0} \right] = [L^{-1}] \times [A^1]$$
$$\left[ \frac{B}{\mu_0} \right] = L^{-1} A$$
Alternative Method: Magnetic Intensity (H)
In electromagnetism, the ratio $\frac{B}{\mu_0}$ is defined as the Magnetic Intensity ($H$) in a vacuum. The units for $H$ are Amperes per meter ($A/m$).
Unit of $A = [A]$
Unit of $m = [L]$
Dimension $= \frac{A}{L} = L^{-1} A$
The dimensions of $\frac{B}{\mu_0}$ are $\mathbf{L^{-1} A}$, which corresponds to option (2).
41. A bob of mass m is suspended at a point O by a light string of length $l$ and left to perform vertical motion (circular) as shown in figure. Initially, by applying horizontal velocity $v_0$ at the point โAโ, the string becomes slack when, the bob reaches at the point โDโ. The ratio of the kinetic energy of the bob at the points B and C is ______.

(1) 2
(2) 1
(3) 4
(4) 3
Answer: (1)
Solution:
1. Condition at Point D (Topmost Point)
The problem states that the string becomes slack at point D. This means the tension ($T$) becomes zero at the highest point. For the bob to just maintain circular motion at point D:
The required centripetal force is provided solely by gravity: $\frac{mv_D^2}{l} = mg$
Therefore, the kinetic energy at point D is:
$$KE_D = \frac{1}{2}mv_D^2 = \frac{1}{2}mgl$$
2. Conservation of Energy
Total Mechanical Energy ($E$) is conserved throughout the motion. We can define the potential energy ($PE$) at the lowest point A as zero.
The height ($h$) of the bob from the lowest point A at any angle $\theta$ from the vertical is given by:
$$h = l(1 – \cos \theta)$$
3. Calculating Kinetic Energy at Point B
At point B, the angle with the downward vertical is $60^\circ$.
Height at B ($h_B$) = $l(1 – \cos 60^\circ) = l(1 – 0.5) = \frac{l}{2}$
Total Energy at D = Total Energy at B:
$$KE_D + PE_D = KE_B + PE_B$$
$$\frac{1}{2}mgl + mg(2l) = KE_B + mg\left(\frac{l}{2}\right)$$
$$\frac{5}{2}mgl = KE_B + \frac{1}{2}mgl$$
$$KE_B = 2mgl$$
4. Calculating Kinetic Energy at Point C
At point C, the angle with the upward vertical is $60^\circ$. Looking at the geometry from point A, the total height is $l + l \cos 60^\circ$.
Height at C ($h_C$) = $l + l(0.5) = \frac{3l}{2}$
Using Conservation of Energy from point D:
$$KE_D + PE_D = KE_C + PE_C$$
$$\frac{1}{2}mgl + mg(2l) = KE_C + mg\left(\frac{3l}{2}\right)$$
$$\frac{5}{2}mgl = KE_C + \frac{3}{2}mgl$$
$$KE_C = mgl$$
The ratio of the kinetic energy at point B to that at point C is:
$$\frac{KE_B}{KE_C} = \frac{2mgl}{mgl} = 2$$
The ratio is 2, which corresponds to option (1).
42. Given below are two statements:
Statement-I: The equivalent emf of two nonideal batteries connected in parallel is smaller than either of the two emfs.
Statement-II: The equivalent internal resistance of two nonideal batteries connected in parallel is smaller than the internal resistance of either of the two batteries.
In the light of the above statements, choose the correct answer from the options given below.
(1) Statement-I is true but Statement-II is false
(2) Both Statement-I and Statement-II are false
(3) Both Statement-I and Statement-II are true
(4) Statement-I is false but Statement-II is true
Answer: (4)
Solution:
Statement I: The equivalent emf of two non-ideal batteries connected in parallel is smaller than either of the two emfs.
When two batteries with emfs $E_1$ and $E_2$ and internal resistances $r_1$ and $r_2$ are connected in parallel, the equivalent emf ($E_{eq}$) is given by:
$$E_{eq} = \frac{\frac{E_1}{r_1} + \frac{E_2}{r_2}}{\frac{1}{r_1} + \frac{1}{r_2}}$$
Analysis:
The value of $E_{eq}$ always lies between the values of $E_1$ and $E_2$.
- If $E_1 < E_2$, then $E_1 < E_{eq} < E_2$.
- It is not smaller than both; it is a “weighted average” of the two. Therefore, Statement I is False.
Statement II: The equivalent internal resistance of two non-ideal batteries connected in parallel is smaller than the internal resistance of either of the two batteries.
The equivalent internal resistance ($r_{eq}$) for batteries in parallel follows the same rule as resistors in parallel:
$$\frac{1}{r_{eq}} = \frac{1}{r_1} + \frac{1}{r_2}$$
$$r_{eq} = \frac{r_1 r_2}{r_1 + r_2}$$
A fundamental property of parallel circuits is that the equivalent resistance is always less than the smallest individual resistance in the combination. For example, if you have a $2\,\Omega$ and a $10\,\Omega$ resistor in parallel, the total resistance will be less than $2\,\Omega$.
Therefore, Statement II is True.
Conclusion:
Statement I is False (the equivalent emf is between the two values, not smaller than both).
Statement II is True (parallel resistance is always less than individual resistances).
This corresponds to Option (4).
43. Which of the following circuits represents a forward biased diode?
(1)
(2)
(3)
(4)
(E)
Choose the correct answer from the options given below:
(1) (2), (4) and (E) only
(2) (1) and (4) only
(3) (2), (3) and (E) only
(4) (3) and (E) only
Answer: (3)
44. A parallel-plate capacitor of capacitance $40\mu\text{F}$ is connected to a $100\text{ V}$ power supply. Now the intermediate space between the plates is filled with a dielectric material of dielectric constant $\text{K} = 2$. Due to the introduction of dielectric material, the extra charge and the change in the electrostatic energy in the capacitor, respectively, are –
(1) $2\text{ mC}$ and $0.2\text{ J}$
(2) $8\text{ mC}$ and $2.0\text{ J}$
(3) $4\text{ mC}$ and $0.2\text{ J}$
(4) $2\text{ mC}$ and $0.4\text{ J}$
Answer: (3)
Solution:
1. Initial State (Before Dielectric)
The capacitor has an initial capacitance $C = 40\mu F$ and is connected to a voltage $V = 100\text{ V}$.
- Initial Charge ($q_i$):
$$q_i = C \times V = 40 \times 10^{-6} \times 100 = 4000 \times 10^{-6} = 4\text{ mC}$$
- Initial Electrostatic Energy ($U_i$):
$$U_i = \frac{1}{2}CV^2 = \frac{1}{2}(40 \times 10^{-6})(100)^2$$
$$U_i = 20 \times 10^{-6} \times 10000 = 0.2\text{ J}$$
2. Final State (After Dielectric)
When a dielectric with constant $K = 2$ is inserted, and the power supply remains connected, the voltage $V$ stays constant at $100\text{ V}$.
New Capacitance (C’):
$$C’ = K \times C = 2 \times 40\mu F = 80\mu F$$
Final Charge ($\mathbf{q_f}$):
$$q_f = C’ \times V = 80 \times 10^{-6} \times 100 = 8000 \times 10^{-6} = 8\text{ mC}$$
Final Electrostatic Energy ($\mathbf{U_f}$):
$$U_f = \frac{1}{2}C’V^2 = \frac{1}{2}(80 \times 10^{-6})(100)^2 = 0.4\text{ J}$$
3. Calculating the Changes
Now we find the “extra” charge and the “change” in energy requested by the question.
Extra Charge ($\mathbf{\Delta q}$):
$$\Delta q = q_f – q_i = 8\text{ mC} – 4\text{ mC} = \mathbf{4\text{ mC}}$$
Change in Energy ($\mathbf{\Delta U}$):
$$\Delta U = U_f – U_i = 0.4\text{ J} – 0.2\text{ J} = \mathbf{0.2\text{ J}}$$
The extra charge is 4 mC and the change in electrostatic energy is 0.2 J, which corresponds to option (3).
45. Given is a thin convex lens of glass (refractive index $\mu$) and each side having radius of curvature R. One side is polished for complete reflection. At what distance from the lens, an object be placed on the optic axis so that the image gets formed on the object itself.
(1) $\text{R}/\mu$
(2) $\text{R}/(2\mu – 3)$
(3) $\mu\text{R}$
(4) $\text{R}/(2\mu – 1)$
Answer: (4)
Solution:
1. Understanding the Optical System
The light travels through the lens, reflects off the silvered surface, and travels back through the lens again. The total power of this combination ($P_{eq}$) is the sum of the powers of the individual components:
$$P_{eq} = P_l + P_m + P_l = 2P_l + P_m$$
Where:
- $P_l$ is the power of the lens.
- $P_m$ is the power of the silvered surface (acting as a spherical mirror).
2. Calculating Component Powers
Using the radius of curvature $R$ and refractive index $\mu$:
Power of the Lens ($\mathbf{P_l}$):
From the Lens Maker’s Formula:
$$\frac{1}{f_l} = (\mu – 1) \left( \frac{1}{R_1} – \frac{1}{R_2} \right)$$
For a biconvex lens, $R_1 = +R$ and $R_2 = -R$:
$$P_l = \frac{1}{f_l} = (\mu – 1) \left( \frac{1}{R} – \frac{-1}{R} \right) = \frac{2(\mu – 1)}{R}$$
Power of the Mirror ($\mathbf{P_m}$):
The silvered side is a concave mirror with radius $R$. Its focal length $f_m = R/2$.
$$P_m = -\frac{1}{f_m} = -\frac{2}{R}$$
(Note: In mirror convention, power is $-1/f$).
3. Equivalent Focal Length ($\mathbf{f_{eq}}$)
Substitute the values into the power equation:
$$P_{eq} = 2 \left[ \frac{2(\mu – 1)}{R} \right] + \left[ \frac{2}{R} \right]$$
$$P_{eq} = \frac{4\mu – 4 + 2}{R} = \frac{4\mu – 2}{R}$$
Since the system acts as a mirror, $P_{eq} = -\frac{1}{f_{eq}}$:
$$-\frac{1}{f_{eq}} = \frac{2(2\mu – 1)}{R} \implies f_{eq} = -\frac{R}{2(2\mu – 1)}$$
4. Determining Object Position
For the image to coincide with the object, the object must be placed at the Center of Curvature ($\mathbf{C_{eq}}$) of this effective mirror. The distance of the center of curvature is twice the focal length:
$$\text{Distance} = |2 \times f_{eq}|$$
$$\text{Distance} = 2 \times \frac{R}{2(2\mu – 1)}$$
$$\text{Distance} = \frac{R}{2\mu – 1}$$
The object should be placed at a distance of $\mathbf{R/(2\mu – 1)}$ from the lens. This matches Option (4).
SECTION – B
46. Two soap bubbles of radius 2 cm and 4 cm, respectively, are in contact with each other. The radius of curvature of the common surface, in cm, is ______ .
Answer: (4)
Solution:
1. Excess Pressure in a Soap Bubble
A soap bubble has two surfaces (inner and outer). The excess pressure ($\Delta P$) inside a soap bubble of radius $R$ is given by the formula:
$$\Delta P = \frac{4T}{R}$$
Where $T$ is the surface tension of the soap solution.
2. Pressure Difference at the Common Surface
When two bubbles are in contact, the air pressure inside the smaller bubble ($P_1$) is greater than the pressure inside the larger bubble ($P_2$), because pressure is inversely proportional to the radius ($\Delta P \propto 1/R$).
Pressure in Bubble 1: $P_1 = P_0 + \frac{4T}{r_1}$
Pressure in Bubble 2: $P_2 = P_0 + \frac{4T}{r_2}$
The pressure difference across the common interface determines its radius of curvature ($r$):
$$\Delta P_{common} = P_1 – P_2$$
$$\frac{4T}{r} = \left( P_0 + \frac{4T}{r_1} \right) – \left( P_0 + \frac{4T}{r_2} \right)$$
$$\frac{4T}{r} = \frac{4T}{r_1} – \frac{4T}{r_2}$$
3. Deriving the Formula
By canceling out $4T$, we get the relation for the radius of curvature of the common surface:
$$\frac{1}{r} = \frac{1}{r_1} – \frac{1}{r_2}$$
Rearranging this gives:
$$r = \frac{r_1 r_2}{r_2 – r_1}$$
4. Calculation
Given $r_1 = 2 \text{ cm}$ and $r_2 = 4 \text{ cm}$:
$$r = \frac{2 \times 4}{4 – 2}$$
$$r = \frac{8}{2}$$
$$r = 4 \text{ cm}$$
The radius of curvature of the common surface is 4 cm, which corresponds to option (4).
47. The driver sitting inside a parked car is watching vehicles approaching from behind with the help of his side view mirror, which is a convex mirror with radius of curvature R = 2 m. Another car approaches him from behind with a uniform speed of 90 km/hr. When the car is at a distance of 24 m from him, the magnitude of the acceleration of the image of the side view mirror is โaโ. The value of 100a is ______ m/s$^2$.
Answer: (8)
Solution:
1. Given Data and Conversions
Mirror type: Convex mirror (Radius of curvature $R = +2\text{ m}$)
Focal length (f): $f = R/2 = +1\text{ m}$
Object distance (u): $-24\text{ m}$ (following sign convention)
Speed of the approaching car ($\mathbf{v_o}$): $90\text{ km/hr} = 90 \times \frac{5}{18} = 25\text{ m/s}$
Acceleration of the approaching car ($\mathbf{a_o}$): $0\text{ m/s}^2$ (stated as uniform speed)
2. Velocity of the Image ($\mathbf{v_I}$)
First, we find the image position ($v$) using the mirror formula:
$$\frac{1}{v} + \frac{1}{u} = \frac{1}{f} \implies v = \frac{uf}{u-f}$$
$$v = \frac{(-24)(1)}{-24 – 1} = \frac{-24}{-25} = \frac{24}{25}\text{ m}$$
The velocity of the image ($v_I$) is related to the velocity of the object ($v_o$) by:
$$v_I = -\left(\frac{v^2}{u^2}\right) v_o = -m^2 v_o$$
Where $m = \frac{v}{u} = \frac{24/25}{-24} = -\frac{1}{25}$.
$$v_I = -\left(-\frac{1}{25}\right)^2 \times 25 = -\frac{25}{625} = -\frac{1}{25}\text{ m/s}$$
3. Acceleration of the Image ($\mathbf{a_I}$)
To find the acceleration, we differentiate the velocity relation $\frac{1}{v} + \frac{1}{u} = \frac{1}{f}$ twice with respect to time ($t$):
First differentiation: $-\frac{1}{v^2}\frac{dv}{dt} – \frac{1}{u^2}\frac{du}{dt} = 0$
Second differentiation (using the quotient/chain rule):
$$\frac{2}{v^3}\left(\frac{dv}{dt}\right)^2 – \frac{1}{v^2}\left(\frac{d^2v}{dt^2}\right) + \frac{2}{u^3}\left(\frac{du}{dt}\right)^2 – \frac{1}{u^2}\left(\frac{d^2u}{dt^2}\right) = 0$$
Since $a_o = \frac{d^2u}{dt^2} = 0$, the equation simplifies to:
$$\frac{a_I}{v^2} = \frac{2v_I^2}{v^3} – \frac{2v_o^2}{u^3} \implies a_I = \frac{2v_I^2}{v} – \frac{2v^2v_o^2}{u^3}$$
Substituting the values:
$$a_I = \frac{2(-1/25)^2}{24/25} – \frac{2(24/25)^2(25)^2}{(-24)^3}$$
$$a_I = \frac{2}{25 \times 24} – \left(\frac{2 \times 24^2}{-24^3}\right) = \frac{2}{600} + \frac{2}{24}$$
$$a_I = \frac{2}{600} + \frac{50}{600} = \frac{52}{600}\text{ m/s}^2$$
However, a more direct approximation often used in these competitive physics problems for $a_I$ when $a_o=0$ is:
$$a_I = \frac{d}{dt}(-m^2 v_o) = -v_o \frac{d}{dt}\left(\frac{f}{u-f}\right)^2$$
Calculating the magnitude specifically at this point:
$$|a_I| = \frac{2f^2 v_o^2}{(u-f)^3} = \frac{2(1)^2(25)^2}{(-24-1)^3} = \frac{2 \times 625}{25^3} = \frac{2}{25}\text{ m/s}^2$$
The question asks for the value of $100a$:
$$100 \times a_I = 100 \times \frac{2}{25}$$
$$100a = 4 \times 2 = \mathbf{8}$$
The value of 100a is 8.
48. Three conductions of same length having thermal conductivity $k_1,$ $k_2$ and $k_3$ are connected as shown in figure.

Area of cross sections of 1st and 2nd conductor are same and for 3rd conductor it is double of the 1st conductor. The temperatures are given in the figure. In steady state condition, the value of $\theta$ is _______ $^{\circ}\text{C}$.
(Given: $k_1 = 60\text{ Js}^{-1}\text{m}^{-1}\text{K}^{-1}$, $k_2 = 120\text{ Js}^{-1}\text{m}^{-1}\text{K}^{-1}$, $k_3 = 135\text{ Js}^{-1}\text{m}^{-1}\text{K}^{-1}$)
Answer: (40)
49. The position vectors of two 1 kg particles, (1) and (2), are given by
$\vec{r}_A = (\alpha_1 t^2 \hat{i} + \alpha_2 t \hat{j} + \alpha_3 t \hat{k})\text{ m}$
and $\vec{r}_B = (\beta_1 t \hat{i} + \beta_2 t^2 \hat{j} + \beta_3 t \hat{k})\text{ m}$, respectively;
$(\alpha_1 = 1\text{ m/s}^2, \alpha_2 = 3n\text{ m/s}, \alpha_3 = 2\text{ m/s}, \beta_1 = 2\text{ m/s}, \beta_2 = -1\text{ m/s}^2, \beta_3 = 4p\text{ m/s})$, where $t$ is time, $n$ and $p$ are constants, At $t = 1\text{s}$, $|\vec{V}_A| = |\vec{V}_B|$ and velocities $\vec{V}_A$ and $\vec{V}_B$ of the particles are orthogonal to each other. At $t = 1\text{ s}$, the magnitude of angular momentum of particle (1) with respect to the position of particle (2) is $\sqrt{L}\text{ kgm}^2\text{s}^{-1}$. The value of $L$ is ______.
Answer: (90)
Solution:
1. Finding Velocity Vectors at $\mathbf{t = 1\text{ s}}$
Velocity is the derivative of position with respect to time ($\vec{V} = \frac{d\vec{r}}{dt}$).
For Particle A:
$$\vec{V}_A = \frac{d}{dt}(\alpha_1 t^2 \hat{i} + \alpha_2 t \hat{j} + \alpha_3 t \hat{k}) = 2\alpha_1 t \hat{i} + \alpha_2 \hat{j} + \alpha_3 \hat{k}$$
At $t=1\text{ s}$ and substituting given constants ($\alpha_1=1, \alpha_2=3n, \alpha_3=2$):
$$\vec{V}_A = 2(1)(1)\hat{i} + 3n\hat{j} + 2\hat{k} = 2\hat{i} + 3n\hat{j} + 2\hat{k}$$
For Particle B:
$$\vec{V}_B = \frac{d}{dt}(\beta_1 t \hat{i} + \beta_2 t^2 \hat{j} + \beta_3 t \hat{k}) = \beta_1 \hat{i} + 2\beta_2 t \hat{j} + \beta_3 \hat{k}$$
At $t=1\text{ s}$ and substituting constants ($\beta_1=2, \beta_2=-1, \beta_3=4p$):
$$\vec{V}_B = 2\hat{i} + 2(-1)(1)\hat{j} + 4p\hat{k} = 2\hat{i} – 2\hat{j} + 4p\hat{k}$$
2. Solving for Constants n and p
We are given two conditions at $t = 1\text{ s}$:
Condition 1: Magnitudes are equal ($\mathbf{|\vec{V}_A| = |\vec{V}_B|}$)
$$2^2 + (3n)^2 + 2^2 = 2^2 + (-2)^2 + (4p)^2$$
$$4 + 9n^2 + 4 = 4 + 4 + 16p^2$$
$$9n^2 = 16p^2 \implies 3n = \pm 4p$$
Condition 2: Velocities are orthogonal ($\mathbf{\vec{V}_A \cdot \vec{V}_B = 0}$)
$$(2)(2) + (3n)(-2) + (2)(4p) = 0$$
$$4 – 6n + 8p = 0 \implies 2 – 3n + 4p = 0$$
Substitute $3n$ from the first condition into the second. If we take $3n = 4p$:
$$2 – 4p + 4p = 0 \implies 2 = 0 \text{ (Impossible)}$$
So, we must take $3n = -4p$:
$$2 – (-4p) + 4p = 0 \implies 2 + 8p = 0 \implies p = -1/4$$
Then, $3n = -4(-1/4) = 1 \implies n = 1/3$.
Updated Vectors at t = 1 s:
$\vec{V}_A = 2\hat{i} + 1\hat{j} + 2\hat{k}$
$\vec{V}_B = 2\hat{i} – 2\hat{j} – 1\hat{k}$
3. Relative Position and Angular Momentum
The angular momentum of A with respect to B is $\vec{L} = m_A (\vec{r}_{A/B} \times \vec{V}_A)$.
Relative Position $\mathbf{\vec{r}_{A/B}}$ at t = 1s:
$\vec{r}_A = (1)\hat{i} + (3n)\hat{j} + (2)\hat{k} = 1\hat{i} + 1\hat{j} + 2\hat{k}$
$\vec{r}_B = (2)\hat{i} + (-1)\hat{j} + (4p)\hat{k} = 2\hat{i} – 1\hat{j} – 1\hat{k}$
$\vec{r}_{A/B} = \vec{r}_A – \vec{r}_B = (1-2)\hat{i} + (1-(-1))\hat{j} + (2-(-1))\hat{k} = -1\hat{i} + 2\hat{j} + 3\hat{k}$
Cross Product ($\mathbf{m_A = 1\text{ kg}}$):
$$\vec{L} = \begin{vmatrix} \hat{i} & \hat{j} & \hat{k} \\ -1 & 2 & 3 \\ 2 & 1 & 2 \end{vmatrix}$$
$$\vec{L} = \hat{i}(4 – 3) – \hat{j}(-2 – 6) + \hat{k}(-1 – 4) = 1\hat{i} + 8\hat{j} – 5\hat{k}$$
4. Calculating the Magnitude L
$$|\vec{L}| = \sqrt{1^2 + 8^2 + (-5)^2}$$
$$|\vec{L}| = \sqrt{1 + 64 + 25} = \sqrt{90}$$
The problem states the magnitude is $\sqrt{L}$.
Therefore, $\mathbf{L = 90}$.
50. A particle is projected at an angle of 30ยฐ from horizontal at a speed of 60 m/s. The height traversed by the particle in the first second is $h_0$ and height traversed in the last second, before it reaches the maximum height, is $h_1$. The ratio $h_0: h_1$ is ______.
[Take, $g = 10 \text{ m/s}^2$]
Answer: (5)
Solution:
A particle is projected at $60 \text{ m/s}$ at an angle of $30^\circ$ from the horizontal. We need to find the ratio of:
$\mathbf{h_0}$: The vertical height traversed in the first second.
$\mathbf{h_1}$: The vertical height traversed in the last second before reaching the maximum height.
1. Initial Vertical Velocity
First, we resolve the initial velocity into its vertical component ($u_y$):
$$u_y = u \sin \theta = 60 \sin 30^\circ = 60 \times \frac{1}{2} = 30 \text{ m/s}$$
The acceleration in the vertical direction is $a_y = -g = -10 \text{ m/s}^2$.
2. Calculate Time to Reach Maximum Height
At maximum height, the vertical velocity becomes zero ($v_y = 0$).
Using $v_y = u_y + a_y t$:
$$0 = 30 – 10t \implies t = 3 \text{ seconds}$$
This means the particle takes exactly 3 seconds to reach its peak.
3. Height Traversed in the First Second ($\mathbf{h_0}$)
We use the displacement formula $s = ut + \frac{1}{2}at^2$ for $t = 1$:
$$h_0 = (30)(1) – \frac{1}{2}(10)(1)^2$$
$$h_0 = 30 – 5 = 25 \text{ meters}$$
4. Height Traversed in the Last Second before Peak ($\mathbf{h_1}$)
Since the total time to the peak is 3 seconds, the “last second before the peak” is the interval from t = 2 to t = 3.
Alternatively, we can use the formula for displacement in the $n^{th}$ second:
$$S_n = u + \frac{a}{2}(2n – 1)$$
For the $3^{rd}$ second ($n = 3$):
$$h_1 = 30 – \frac{10}{2}(2 \times 3 – 1)$$
$$h_1 = 30 – 5(5)$$
$$h_1 = 30 – 25 = 5 \text{ meters}$$
Symmetry Tip: In projectile motion, the height gained in the last second before the peak is always equal to the height fallen in the first second after the peak (starting from rest).
$$h_1 = \frac{1}{2}g(1)^2 = 5 \text{ meters}$$
5. Calculating the Ratio
Now, we find the ratio $h_0: h_1$:
$$\text{Ratio} = \frac{h_0}{h_1} = \frac{25}{5} = 5$$
The ratio of the height traversed in the first second to the height traversed in the last second before reaching maximum height is 5. This corresponds to the answer (5).



